The solid shaft AB has a d= (3.5 + 0.4 a) in. and shaft BC has a d shafts AB and BC have the same E 20,000 ksi. Determine the reaction at A and C. Use the horizontal support at C as the redundant support. (Note: Give your answers in units of kips using 4 significant digits of accuracy.) Lo Lo Lo = (18 +b) inches P= (35 +c) kips B dBc A dAB

The solid shaft AB has a d= (3.5 + 0.4 a) in. and shaft BC has a d shafts AB and BC have the same E 20,000 ksi. Determine the reaction at A and C. Use the horizontal support at C as the redundant support. (Note: Give your answers in units of kips using 4 significant digits of accuracy.) Lo Lo Lo = (18 +b) inches P= (35 +c) kips B dBc A dAB

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.3P

See similar textbooks

Similar questions

, Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14 kN/m, and L = L2 m.
Steel bar in shape, AAB 600 mm and ABc = DACD3D 1200 mm2 are made of two stages. Determine the displacement at end A in (mm). E = 200 GPa
The A36 steel shafts as shown in the figure below are made from two segments: solid segment AC with diameter = 1 in and a hollow segment CB with an outside diameter = 2 in and inside diameter = 1 in. The shaft is fixed at both ends. Determine the magnitude of the applied torque T (lb-in) if the reaction at A is 600 lb-in clockwise.
Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is fixed at both ends. Section AC is solid with a diameter of do = 80 mm, while CB is a hollow section with an internal diameter of di = 60 mm. An external torque T0 = 10 kN.m is applied at point D. (a) Determine the magnitude of the reaction torques at both supports if the distance x = 735 mm.
A solid circular shaft has a diameter of d mm and is made from steel, which fail when tested in simple tension test at a stress of 150 MPa. The shaft was subjected by bending moment and torque which are 22.2 kNm and 44.4 kNm respectively. Calculate the minimum allowable shaft diameter, d according to:- (a) Tresca failure criterion (b) Von Mises theory of elastic failure
The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the torques 2T and 3T at points A and B, respectively. If tallow = 35 MPa and (fA/C)allow =2o, determine the maximum permissible value of the torque T. Use the table given below and your student ID to find the values of L1, L2, and D. Student ID L1 (m) L2 (m) D (mm) 1131731 1 0.6 78
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (Sf) is equal to 0.8 Su and endurance Strength (Se) is equal to 0,5 Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S-N diagram
Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively. The material has-a shear modulus of 60 kN/mm'. Determine the maximum stress in the shaft when it is subjected to a twist of 5 in a length of 2.5 m. What is the maximum torque the shaft can carry? For a circle / = nd*/32.
Two sections of steel drill pipe, joined by boltedflange plates at B, are being tested to assess the adequacyof both the pipes. In the test, the pipe structureis fixed at A, a concentrated torque of 500 kN ? m isapplied at x = 0.5 m, and uniformly distributed torqueintensity t0 = 250 kN . m/m is applied on pipe BC.Both pipes have the same inner diameter d = 200 mm.Pipe AB has thickness tAB =15 mm, while pipe BChas thickness tBC =12 mm. Find the maximum shearstress and maximum twist of the pipe and their locationsalong the pipe. Assume G = 75 GPa.
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength ( Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (S) is equal to 0.8Su and endurance Strength (Se) is equal to 0, 5Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S - N diagram
The following shaft, having a diameter of 20 mm, is made of steel (Sut = 520 MPa, Se = 260 MPa) and is subjected to a fully reversed transverse force F = 120 N and a fully reversed torque T = 60 N.m. The shaft is fixed at its left end. Find the factor of safety at A for infinite lifetime using the modified Goodman diagram.
A shaft is made of bronze at length AB and steel at length BC fixed at both ends. It is subjected to a concentrated torsional moment at the junction, The steel segment is 1 meter long. Assume that the Bronze has a diameter of 75mm, G = 35 GPa and τ = 60 MPa whilst the steel has a diameter of 50mm, G = 80 GPa, and τ = 80 MPa. What is the reaction at the left end if the maximum torque is applied to the saft, in kN.