30 mm PROBLEM 3.2 (a) Determine the torque T that causes a maximum shearing stress of 45 MPa in the hollow cylindrical steel shaft shown. (b) Determine the maximum shearing stress caused by the same torque T in a solid cylindrical 45 mm 2.4 m shaft of the same cross-sectional area. T = 5.17 kN - m T = 87.2 MPa

30 mm PROBLEM 3.2 (a) Determine the torque T that causes a maximum shearing stress of 45 MPa in the hollow cylindrical steel shaft shown. (b) Determine the maximum shearing stress caused by the same torque T in a solid cylindrical 45 mm 2.4 m shaft of the same cross-sectional area. T = 5.17 kN - m T = 87.2 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stepped shaft shown rotates at 480 rpm. Knowing that r = 0.2 in. and using figure 3.28, determine the largest torque T that can be transmitted without exceeding an allowable shearing stress of 7000 psi.
The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa. Neglecting the effect of stress concentrations, determine the smallest diameters dAB and dBC for which the allowable shearing stress is not exceeded. For the Problem, without changing the total length of the shaft, where would you move Point B such that the totalangular rotation at point C is twice thatatpoint B. Explain yourassumptions and your work in detail.(B)Given a cube of materialwith the given peoperties E and ν. Assumethatσx= σz= σo;εx=εz=εoandεy=0.Determineσoas a function ofεoandσyas a function ofσo.Explain.
A solid shaft having a diameter of 100mm has an allowable shearing stress of 80 MPa. Determine the maximum torque in KN-m that the shaft can carry without exceeding the allowable shearing stress.
Torsion Problem: A solid circular shaft of diameter 220 mm is to be replaced by a hollow shaft in which the ratio of the diameters is 2:1. Determine the size of the required to transmit the same torque as the solid shaft at the same maximum shearing stress.
A flange bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 60 MN/m2, how many 10-mm diameter steel bolts must be used on a 200-mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
A flange coupling is to be designed, using 6 bolts at a distance of 89 mm from the center of the shaft, allowable shearing stress on the bolt is 103 MPa. If the shaft is to transmit 4035hp at a speed of 1200 rpm, (a) determine the bolt diameter required in mm. (b) If the shaft is made of the same material as the bolt, determine the required diameter of the shaft in mm.
Calculate the maximum permissible torque on a hollow shaft if the maximum allowable shearing stress is 83 MPa. D=75mm and d=60mm. A)4788 Nm B)4316 Nm C)4059 Nm D)4532 Nm
A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diam-eters respectively equal to 40 and 60 mm ). (a) What is the larg-est torque that can be applied to the shaft if the shearing stress is not to exceed 120 MPa? (b) What is the corresponding minimum value of the shearing stress in the shaft?
A propeller shaft in a ship is 400 mm in diameter and 6 m in length. The allowable shearing stress is 60 MPa and the allowable angle of twist is 2°.If G= 65GPa, determine the maximum torque the shaft can transmit.
A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so as not to exceed a shearing stress of 42 MPa and an angle of twist of more than 5 degrees in a length of 3 meters. G = 83 GPa
Give a complete solution, Don't use the direct formula. [1] A semicircular groove with a 5-mm radius is required in a 110-mm diameter shaft. If the maximum shearing stress in the shaft must be limited to 60 MPa, determine the maximum torque that can be transmitted by the shaft.
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.