The three flat blocks are positioned on the 300 incline as shown in Figure2, and a force P parallel to the incline is applied to the middle block. The upper block is prevented from moving by a wire which attaches it to the fixed support. The coefficient of static friction for each of the three pairs of mating surfaces is shown. Determine the maximum value which P may have before any slipping takes place. [

Q: n the figure shown, compute the minimum value of θ so that there is impending motion of the block.…

A: To determine the minimum value of θ

Q: (b) The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown…

A:

Q: The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in…

A:

Q: Using the provided information, compete the following problems. • The system shown is in static…

A: (8) Write the static coefficient of friction at rope/shaft interface. Write the kinetic coefficient…

Q: Solve each of the following problems indicated below. Present your complete-detail solution…

A: Write the given value using suitable variables. Here Tmax signifies cord maximum tension and μs…

Q: In the figure shown, compute the minimum weight W to prevent impending motion of the block up the…

A: Given:- m=100lb θ=45° μ=0.45 To find:- Weight of W

Q: For the drum brake shown in the following figure, there is an inner rim diameter of 280 mm and…

A:

Q: A 5.0kg steel block is resting on a horizontal table. The coefficient of static friction is 0.75 and…

A: limiting friction =  μ N   μ  = coefficient of friction N = normal reaction

Q: The pulley of Fig. wheel that fits loosely over a t in.-diameter shaft. A rope passes over the…

A: Given: The diameter of the wheel, D = 4 in The diameter of the shaft, d = ½ in The magnitude of…

Q: the driving shaft and make contact with the internal cylindrical surface of a rim keyed to the…

A: Given: The number of shoe, n = 4 The radial clearance between shoe lining and drum, x = 5 mm The…

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Free-body diagrams of the drum and handle are given as, On considering the free-body diagram of the…

Q: The band brake of Fig is used to control the rotation of a drum. The weight of the handle is 2 lb.…

A: Draw the free-body diagram of the handle when the rotation of the drum is clockwise.

Q: 3. A 300 lb block rests on a horizontal surface. The coefficient of static friction between the…

A:

Q: The effective pressure on a 400 mm diameter piston is 1.1 MN/m² when the crank is 32° beyond top…

A: Given: Diameter of the piston→D=400 mm=0.4 m So area of the piston→A=π4×D2=π4×0.42=0.125 m2 Pressure…

Q: For the drum brake figure shown below a) If a couple M of magnitude 1xy N.m is applied to the drum…

A: (a) Free body diagram the fig I and fig II showing the free body diagram of drum brake shown below…

Q: The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in…

A: given; torque(T)=7Nmcoefficient of friction(μ)=0.35angle(θ)=600            =π180*60…

Q: A lightweight rope is wrapped around a drum as shown in Fig. drum and the ground is 0.30. Determine…

A: Draw the free body diagram for the above system.

Q: Q2. Each of the two blocks in Figure 10.4 has a mass of 10 kg, and the coefficient of friction…

A:

Q: The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in…

A:

Q: Figure shows a friction brake in which the curved lever BC is pivoted at the fixed-point and carries…

A:

Q: A uniform ladder of length f rests against a smooth, vertical wall (figure (a)). The mass of the…

A: Solution given data

Q: A square threaded screw of mean diameter 25 mm and pitch of thread 6 mm is utilised to lift a weight…

A:

Q: the driving shaft and make contact with the internal cylindrical surface of a rim keyed to the…

A: Given, No. of shoes, n=4Clearance, C=5mmSpring force, S=500NMass of each shoe, m=8kgStiffness of…

Q: According to the results In Figure 3 of the following If the m = 15 Kg, 0 = 30° (A-The static…

A:

Q: Question Find the least value of P required to cause the system of blocks shown in figure below to…

A: Given, Mass of block 1 M1 = 30 kN Weight of block 2  W2 = 10 kN μ = 0.22

Q: In the figure shown the blocks weighs 400 N each. It is held in the position by a belt that passes…

A:

Q: A pull of 31.89 N at 30° to the horizontal in necessary to move a block of wood on a horizontal…

A: Given data: Consider the FBD of the system.

Q: A uniform ladder 5 m long and weighing 80N rests against on a vertical wall at B and one end at A…

A:

Q: Problem -02 Dry FrictionKnowing that a couple of magnitude 30 N m is required to start the vertical…

A:

Q: Calculate the minimum distance, x so that the bracket can support the cylinder of any mass without…

A: Draw the FBD for the given question.

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: First, draw the free-body diagram of the handle: Now write the momentum equation about the point O.…

Q: The electric motor shown in Fig. and delivers 50 in. Ib of torque to pulley A of a furnace blower by…

A: Given:Torque about pulley,TP=50 lb-inDiameter of pulley,D=5 inAngle made by V pulley,α=36οWeight of…

Q: A lifting mechanism as shown has two single-lead 3/4“ diameter ACME thread screws. The thread…

A: Given Information: The diameter of the screws (d) = 3/4 inches The coefficient of friction (µ) =…

Q: The 2225 N block shown is in contact with 45° incline. The coefficient of static friction is 0.25.…

A: Given data as per question weight of block = 2225 N The coefficient of static friction = 0.25.…

Q: 1. The blocks shown in the figure below are separated by a solid strut which is attached to the…

A: mrod=100 lbμ=0.2mass of block 1=400 lbmass of block 2=200 lb

Q: The pressure distribution at the pivot bearing's surface of contact changes, as indicated. Determine…

A: Given data Friction as considered for calculating the Torque. Where Pressure are distributed as on…

Q: The two wedges are stacked as shown in figure 1. a.) What is the total reaction at the wall if the…

A:

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A:

Q: Refer to Fig 33. The homogenous body A weighs 120 lb. The coefficients of frictions are 0.30 between…

A:

Q: • The system shown is in static equilibrium and motionless. • Consider the 10 kN force as "the load"…

A: Given, Static friction, μs=0.25Dynamic friction, μk=0.16Load, W=10KN Angle of wrap around the upper…

Q: In the figure shown the weights of the blocks are WA = 100 lb and WB  =25 lb. Between all of the…

A:

Q: The figure shows a system with a block m1 attached to a simple square thread screw with a mean…

A:

Q: Q / If (300 Kg) block shown in figure(1) has impending motion up the plane caused by the horizontal…

A: Given Data: The mass of the block is, m=300 kg. The force applied on the block is, F=5000 N.

Q: Answer the following questions about the exercise of Box A (massmA=50kg) and Box B (mB=10kg) located…

A:

Q: value of T for impending tipping

A: Given: To determine: Tension T for impending tipping

Q: (b) The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown…

A: (a) Tension on tight side: Tt = 131.22 N. (b) Tension on slack side: Ts = 14.55 N.

Q: A horizontal arm having a bushing of 20 mm long is slip over a 20-mm diameter vertical rod, as shown…

A:

Q: Problem 4.9 Figure 4.56 illustrates a person who is trying to pull a block on a horizontal surface…

A:

Q: The coefficient of friction between the 120 lb block (shown in figure below) and the incline plane…

A:

Q: A flat belt passes over two idler pulleys and under a rotating drum of diameter 8 in. The axle of…

A: Given, diameter of pully (d) = 8 inchTorque on the drum = 30 lb ftCoeff of static friction between…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.