The transfer coefficient of a certain electrode in contact with M2+ and M3+ in aqueous solution at 25 °C is 0.42. The current density is found to be 17.0 mA cm2 when the overpotential is 105 mV. What is the overpotential required for a current density of 72 mA cm−2? Hint: See hint to Exercise E19D.1(a).

The transfer coefficient of a certain electrode in contact with M2+ and M3+ in aqueous solution at 25 °C is 0.42. The current density is found to be 17.0 mA cm2 when the overpotential is 105 mV. What is the overpotential required for a current density of 72 mA cm−2? Hint: See hint to Exercise E19D.1(a).

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter17: Applications Of Infrared Spectrometry

Section: Chapter Questions

Problem 17.11QAP

See similar textbooks

Similar questions

The classical dissociation constant of propionic acid, C2H5CO2H, is 1.34 x10-5 moldm-3 at 250C and the limiting molar conductivities at zero concentration of hydrogen and propionate ions are 349.8 and 35.8 ohm-1 cm2 mol-1 respectively. Calculation of the resistivity of 0.100 M solution of propionic acid.
How long will it take to dissolve 2 mg of metal A (atomic weight 100) in a solution containing A2+ from a metal electrode with area of 1.5 cm2 at an overpotential of = 0.2 V? The exchange current density (j0) for A is 3x10-3 A/cm2, the temperature T=298 K and the symmetry factor =0.4.
Use the data in Table 19D.1 for the exchange-current density and transfer coefficient for the reaction Fe3+ + e− → Fe2+ on platinum at 25 °C to identify the current density needed to obtain an overpotential of 0.30 V as calculated (i) by using the Butler–Volmer equation, and (ii) by assuming that the current is entirely anodic. Comment on the validity of the latter assumption.
Calculate the effect that increasing the overpotential from 0.50 V to 0.60 V has on the current density in the electrolysis of 1.0 m NaOH(aq), which is 1.22 mA cm−2 at 0.50 V and 25 °C. Take α = 0.50.
Explain why small uncertainties in the measured potential of ISEs can cause large errors in the determined analyte concentration.
3) Name the errors of glass electrodes in potentiometric measurements (please write correctly and concisely).
What is the difference between effect of pH and Point of zero charge with regards to Adsorption
The standard potentials of Pb2+|Pb and Sn2+|Sn are −126 mV and −136 mV respectively at 25 °C, and the overpotential for their deposition are close to zero. What should the relative concentrations of Pb2+(aq) and Sn2+(aq) be in order to ensure simultaneous deposition from a mixture? You may assume that activities can be approximated by molar concentrations.
1) Name the applications of glass electrodes in potentiometric measurements (please write correctly and concisely).
The limiting molar conductivities of KCI, KNO3, and AgNO3 are 14.99 mS m2 mol-1, 14.50 mS m' mol-1, and 13.34 mS m2 mol-1, respectively (all at 25 °C). What is the limiting molar conductivity of AgCI at this temperature?
Nitrogen gas adsorbed on charcoal to the extent of 0.921 cm3 g−1 at 490 kPa and 190 K, but at 250 K the same amount of adsorption was achieved only when the pressure was increased to 3.2 MPa. What is the enthalpy of adsorption of nitrogen on charcoal? Hint: See the hint for Exercise E19B.5(a).
By employing a given conductivity cell with 0.1N potassium chloride at 18pC, an observed conductance of 0.025 mho was obtained. What is the cell constant if the specific conductance of KCL at 18°C is 0.0112 mho.