The transmission system of a blender is given in Figure 1. An electrical motor with power of 8 kW and rotation speed of 1450 rpm is used to run the system. Velocity ratios of the flat-belt drive and the helical- gear drive are 2 and 2,5 respectively. Assuming there is no power lost in the transmission system. Motor Flat-belt drive Helical-gear drive Shaft I 터 Blender Shaft II Coupling

The transmission system of a blender is given in Figure 1. An electrical motor with power of 8 kW and rotation speed of 1450 rpm is used to run the system. Velocity ratios of the flat-belt drive and the helical- gear drive are 2 and 2,5 respectively. Assuming there is no power lost in the transmission system. Motor Flat-belt drive Helical-gear drive Shaft I 터 Blender Shaft II Coupling

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

what factors determine the design of the power transmission mechanisms in a rear wheel drive van (Diesel) and how do you calculate power and torque at the driveshaft, assuming the following: its 5 speed transmission, Gear system efficiency is 88% Gear ratios: 1 st: 4.17:1 2 nd 2.34:1 3 rd 1.52:1 4 th 1.14:1 and power and torque to be calculated at the point where engine is generating its maximum power
A 3000 lb car has a 5-speed manual transmission with 2 .31 ti (transmission ratio) , 1 .22 ti , 4.13 ti , 0 .14 ti , 7 .05 ti . The final drive ratio is 6 .3 ai . The air drag coefficient is 0.32 and the front projected area is 21 square feet. The rolling resistance coefficient is 0.02 and the tire radius is 12 inches. The effective mass factor is 1.0. The power train efficiency is 0.95. The engine wide-open-throttle output torque is shown in the figure. a) Determine the transmission input torque when the vehicle is cruising at a constant speed of 65mph on a 5% slope in the 5th gear. b) When the vehicle speed is 65mph on a 5% slope in the 5th gear, the driver makes a five to four downshift and floors the throttle. Determine the vehicle acceleration immediately after the shift. c) Determine the largest slope the vehicle can negotiate at a speed of 60mph in the 4th gear.
A restaurant owner has decided to install a used fan that could deliver 18,000 CFM of air when running at 320 rpm. The fan is estimated to require at least 4.5 HP to deliver the volume of air needed. The owner has also a second hand motor rated at 5 HP and 1750 rpm. These data are all that the owner could provide you. He would like to use a standard chain and sprocket for the transmission. Use service factor = 1.1 and pitch = 0.5 inch.A) Determine the number of teeth and diameter of small sprocket. B) Determine the number of teeth and diameter of big sprocket. C) Determine the center distance and length of chain.
4.1 Epicyclical gear ratios [Discuss the theoretical method of determining epicyclical gear ratios] 4.2 Determination of efficiency of a gearbox [Discuss the method of determining efficiencies of gearboxes, refer to a dynamic determination] [Note: Reference the theory answers (Link to bibliography)]
Q6. Gear and Motor selection: For a 50 Hz supply frequency, the motor speed is 50 revolutions per second. What gearbox is required to step this down to 2 rad s−1 at the pulley wheel? What is the maximum torque to be developed by the motor? Round off your answers to one decimal place. -The gear ratio required is ? - The maximum torque to be developed by the motor is Nm ?
Note: If you don't know the solution please leave it but don't give me wrong solution. A flat open belt drive is used to transmit a power of 25kW from a motor shaft rotating at 950 rpm. The radius of the pulley of the motor shaft is 125mm while the radius of the puller of the driven shaft is 450mm. The center distance between the shafts is 2,250mm. the coefficient of friction is 0.25 and the density of the belt material is 950 kg/m^3. The belt width is 126 mm. The allowable stress is 2.6MPa. Determine the thickness of the belt.
With a driveshaft turning at 2000 rpm , I then have a spring that can rotate a shaft 5000 rpm, I want this spring to assist in the drive of the driveshaft, how can I express that or calculate the effect of adding the spring would make. Including a spring system alongside a driveshaft that can assist the drive up to 5000rpm, how can I integrate the spring system to assist in the driveshaft drive, calculations on the change in rotation the spring would have of the driveshaft speed
3. Critically discuss the relationship between Pascal’s law and displacement transmission
Q3. Audi’s design of their R8 model is designed in order to have the engine in the rear of the car with the following schematic of their mechanical power transmission. The engine is connected to the gearbox, where gear change occurs and then a driveshaft is used to transfer an equal ratio of power balancing the rear and front wheel power output thus referring to it as an all-wheel drive. The vehicle has been modified by a customer thus resulted to no power transfer to the front wheels although the rear wheels still have the same power output. Using your knowledge, DEFINE and JUSTIFY the possible reasons of why the front drive isn’t functioning. What are the solutions to this fault?
A horizontal belt conveyor arranged as shown in the figure P1 below operates at a speed of 270fpm and requires 25 Hp at the 40-inch-diameter driving drum. The drum receives power from a countershaftthrough a pair of spur gears. A motor operating at 860 rpm delivers power to the countershaft through aroller chain. The mechanical efficiency of the chain drive is 94 % and of the gears is 96 %. a) Determine theHp of the motor you would recommend. b) Determine the rpm of the driving drum and the countershaft. c)Calculate the number of teeth on the large sprocket required running the conveyor belt at the speedspecified. d) Determine the transmitted torque on the countershaft, in in-lb.
The client requires a single step-up spur gearbox to transmit a 10 kW Power from a shaft rotating at 1000 rpm, while output speed must be 1700 rpm. The material of the gear and pinion 817M40 and 655M13, respectively. Use table 6.10 on page 128 to collect suitable gear and pinion. 1.1 briefly state the problem 1.2 State the design specification considering the following design factors a) Functionality b) stress 1.3 State formula and standards relevant to the single step-up spur gearbox design. 1.4 If the pinion has 24 teeth, use the Lewis formula to determine the face width of the pinion and gear. Then, do one set of the calculations and tabulate the answers. 1.5 conclusion
Audi’s design of their R8 model is designed in order to have the engine in the rear of the car with the following schematic of their mechanical power transmission. The engine is connected to the gearbox, where gear change occurs and then a driveshaft is used to transfer an equal ratio of power balancing the rear and front wheel power output thus referring to it as an all-wheel drive. The vehicle has been modified by a customer thus resulted to no power transfer to the front wheels although the rear wheels still have the same power output. 1) DEFINE and JUSTIFY the possible reasons of why the front drive isn’t functioning? 2) What are the solutions to this fault?