Example -7: The uniform smooth rod shown in Fig. is subjected to a force and couple moment. If the rod is supported at A by a smooth wall and at B and C at either the top or bottom by rollers, determine the reactions at these supports. Neglect the weight of the rod. 4 m y 4000 N: m 2m 300 N | 30° 4 1 4000 N m 30° 30 - 2m 300 N 30 C, 30

Example -7: The uniform smooth rod shown in Fig. is subjected to a force and couple moment. If the rod is supported at A by a smooth wall and at B and C at either the top or bottom by rollers, determine the reactions at these supports. Neglect the weight of the rod. 4 m y 4000 N: m 2m 300 N | 30° 4 1 4000 N m 30° 30 - 2m 300 N 30 C, 30

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.5.29P: A steel post (E=30×106) having thickness t = 1/8 in. and height L = 72 in. support a stop sign (see...

See similar textbooks

Similar questions

A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.
A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae= 304 mm2 for each cable) as shown in the figure. A load P = 20 KN is supported at point D. The crane boom lies in the y-z plane. (a) Find the tension forces in each cable: TAQand TBQ(kN}. Neglect the mass of the cables, but include the mass of the boom in addition to load P. (b) Find the average stress (s) in each cable.
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
A steel post (E=30×106) having thickness t = 1/8 in. and height L = 72 in. support a stop sign (see figure), where s = 12.5 in. The height of the post L is measured from the base to the centroid of the sign. The stop sign is subjected to wind pressure p = 20 lb/ft2 normal to its surface. Assume that the post is fixed at its base. What is the resultant load on the sign? (Sec Appendix E, Case 25, for properties of an octagon, n =8.) What is the maximum bending stress in the post? Repeat part (b) if the circular cut-outs arc eliminated over the height of the post.
The figure shows the FBD of a portion of the space truss shown in Fig. P5.25. Use this FBD to find the force in member BD.
Find support reactions at 4 and Band then use the method of joints to find all member forces. Let b = 3 m and P = 80 kN.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
6 A ladder rests against a smooth sloping wall, as shown in Fig. 4.Q6. The vertical load includes the weight of the ladder.Determine the reactions at A and B.
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 9,4 kN. Angle α = 31 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N1 in the rod 1, considering that N1>0 for tension and N1<0 for compression.
A Fixed crane, as given in the figure, has a mass of 1000kg and is used to lift a 2400kg crate. It is held in a place by a point A and a roller B. The center of gravity of a crane is located at G. Determine the components of the reactions at A and B.
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N Which option is right? a) if the plate had a weight of 332N (applied vertically downwards in the center of the plate), the reaction Dy on the plate should be vertical downwards so that the plate still remained in balance in that position or b) if the plate had a weight of 332N (applied vertically downwards in the center of the plate), the reaction Dy on the plate should be vertical downwards so that the plate still remained in balance in that position