Translate the following ARM assembly language instructions into machine code. (a) LDR R11, [R1, R2] (b) STR R8, 4 (RO) (c) SUB R6, R1, R2 LSR #1 (d) LDREQ R10, [RO, #4] (e) BNE -4 9.22

Q: By referring to Figure with a suitable example, discuss what is meant by "greater complexity at the…

A:

Q: This question is from the subject Digital Logic Design. Assume your register number SF20-BEC-xxx…

A:

Q: Place an X under Beam Former, Signal Processor, or Image Processor to identify the location for each…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: How many resistors and switches are required to implement a 10-bit DAC using the technique As…

A: In 3-bit converter, there are 8 possible combination which is 23. For the D/A converter shown in the…

Q: Determine the settings required for a PID controller which gave the process reaction curve shown in…

A:

Q: Q1/Binary to octal conversion (2D9)16 =( )2

A: To convert Base A to Base B, First convert it to the corresponding Decimal value by multiplication…

Q: 8. An 8-bit ADC with a 10.0 V reference has an input of 3.637 V i. Determine the digital output. ii.…

A: Given, 8-bit ADC has  Reference voltage (Vref) = 10.0 V Input voltage (Vi) = 3.637 V

Q: F(A, B, C, D) = Em(0,3,5,8,10,12,13) + Ed (6,7,9,15) a Implement the above function using a 2-1…

A: We need to design the given Boolean function by using of multiplixer .

Q: DIGITAL COMMUNICATION

A:

Q: P. 2. Consider a proposed new instruction named rpt. This instruction combines a loop's condition…

A: A) The most appropriate instruction format seems to be the I-Format Load. Eg. lw x14, 8(x2) here,…

Q: What is interface. What is program block and module block.

A: Interface It is static component which is similar to module does it mean that we can instantiate…

Q: What are Monolithic voltage regulators? Provide an example for Monolithic Voltage regulators

A: A voltage regulator is one of the most widely used electronic circuitry in any device. A regulated…

Q: Discuss the significance of DFT in signal processing applications.

A: DFT(Discrete fourier transform) Convolution of long sequences 1. Overlap add method 2. Overlap save…

Q: - Design a flash ADC with input voltage range [ igital output for a 2.5 V input signal?

A:

Q: Write an 8088/8086 assembly program that counts the length of a null terminated string that starts…

A: Microprocessor Programming : The "jargon" of directions which a specific microchip chip has is…

Q: PID CONTROLLER IN TEMPERATURE CONTROL SYSTEM Please give me a paragraph of introduction about…

A: PID CONTROLLER SETTING IN TEMPERATURE CONTROL SYSTEM.

Q: An SN74AS138 output cannot (reliably)drive an SN74AC08 input when both chips have VCC=4.5 V. Why…

A: According to the datasheet of  SN74AS138 -   At VCC=4.5VThe high-level output voltage is,…

Q: Select all the 8088 input signals that can cause the microprocessor to take an interrupt. O INTR OSC…

A: The 8088 input signals that can cause the microprocessor to take an interrupt is INTR, INTA, and…

Q: Suppose that the contents of certain memory locations are as shown in Figure P8.34. Furthermore, for…

A: Given: FFF, and (Y)=$1000. Name the type of addressing and determine the contents of registers D, X,…

Q: Q) Design 8:1 multiplexer using 4:1 multiplexer and give an example and ?explain why

A: The block diagram of 4x1 MUX is The block diagram of 8x1 MUX is

Q: After executing MOV AX,-11011 SAHF JNC WAQIQI (a) Will the processor jump? (b) repeat the solution…

A: MOV AX, -11011 SAHF JNC WAQIQI (a) will the processor jump after executing this  (b) repeat the…

Q: Compare and contrast SUB and CMP

A:

Q: 2 Determine the High-level noise margins for 5 V CMOS if VIH(mm) = 3.5 V. VIL(nAK)= 3.5 V. VoH(man)…

A:

Q: Design an 8-4-2-1 BCD code converter to drive a seven-segment indicator. The four inputs to the…

A: We need to design an 8-4-2-1 BCD code converter circuit to drive a seven-segment display as shown…

Q: What is Arduino? Select one: O a. A programming environment to control boards and hardware connected…

A: The solution is given below Answer is option B

Q: Which circuit is normally used to perform serial-to-parallel and parallel-to-serial data conversion?…

A: Transmitting each bit of a code one after the another from LSB to MSB, is called serial…

Q: What is the maximum conversion time for a counting ADC using a 12-bit DAC and a 2-MHz clock…

A: Given data: fc=2 MHzn=12 bit The expression for the maximum conversion time is given as,…

Q: Discuss in detail about RAM allocation in 8051 and Analyse, and explain the objective of the…

A:

Q: Verilog is part of the HDL family, what is the definition of HDL: Select one: O a. Hardware…

A: Verilog is an language from a HDL family which is used  for modelling the electronic systems. It is…

Q: Define Quantizer and its Components. How many types of Quantizer can be? What is the need of…

A: A message signal is transferred from the sender to the receiver end. The signal is transmitted…

Q: Design a two way light control then implement the design using: A.PAL realization. B. LUT programme.…

A: Here three questions are given, I am solving A part only because for B part and C part programme and…

Q: Design an 8-4-2-1 BCD code converter to drive a seven-segment indicator. The four inputs to the…

A: A common cathode 7 segment display is when all the led N side is connected to ground. hence giving a…

Q: Investigate as a test of a page, the problems that would arise when implementing the kinematics…

A: By incorporating the notions of nonintegral order derivatives and integrals, fractional-order…

Q: For the given Vin (input voltage), calculate Dout (digital output) in decimal and binary, given the…

A:

Q: (e) This microprocessor uses the specifications shown in Figure Q1(e) for 16-bit floating point…

A: Being a base-16 sustem,the hexadecimal numbering system therefore uses 16(sixteen) diffrent digits…

Q: Suppose a 10-bit DAC is built using the inherently monotonic circuit technique as shown. (a) If the…

A: Concept: A measure of the opposition to current flow in an electrical circuit is defined as…

Q: Draw the schematic diagram of CRT and label the parts. B I II

A:

Q: Q:what is the addressing mode for the following instruction: MOV .(C910), A direct mode Relative…

A:

Q: How many states required to design an FSM machine to process the following sequence, 000111000 3 9.…

A: Finite state machine (FSM) -A Finite State Machine is a device storing the state of something at a…

Q: Explain the Analog to digital conversion in digital signal processing with each step elaborated

A: There are three main things involved in ADC conversion process. First sampled the signal and then…

Q: Assembly-language programs use are which mnemonics, abbreviated instructions zeros and ones, the…

A: Microprocessor : It performs various functions of digital computer. It is the CPU of digital…

Q: Design a 3-Bit (fixed reference) comparator for 100 reference values.  b) Logic Gates  c) PROM  d)…

A: LOGIC GATES: A logic gate is a device that acts as a building block They perform basic logical…

Q: The signals to the inputs of the FFs and registers are shown below. According to this plot the…

A:

Q: 1. Consider the CRC generator shown below. Determine the output of the CRC circuit (i.e. Q4 Q3 Q2 Q1…

A:

Q: a) Sketch a 4-bit R/2R DAC circuit and explain briefly the operating principle b) What should be the…

A: According to the question, we need to explain the 4-bit R-2R ladder DAC circuit.

Q: 8. In a multiplexer, the selection of a particular inpu line is controlled by a) Data controller b)…

A: In this question we will write about multiplexer. .

Q: Microcontrollers- electronics Give three advantages and disadvantages of SPI( Serial Peripheral…

A: Given:  Brief description: Serial peripheral interface is a device which is used to communicate…

Q: Design 3-bit Flash ADC Using Diodes and digital XOR gates

A: Flash ADC is also known as a parallel analog to digital converter. The 3-bit Flash ADC using diodes…

Protection System

A system that protects electrical systems from faults by isolating the problematic part from the remainder of the system, preventing power from being cut from healthy elements, improving system dependability and efficiency is the protection system. Protection devices are the equipment that are utilized to implement the protection system.

Predictive Maintenance System

Predictive maintenance technologies are designed to assist in determining the state of in-service equipment so that maintenance can be scheduled. Predictive maintenance is the application of information; proactive maintenance approaches examine the condition of equipment and anticipate when it should maintain. The purpose of predictive maintenance is to forecast when equipment will fail (depending on a variety of parameters), then prevent the failure through routine and corrective maintenance.Condition monitoring is the continual monitoring of machines during process conditions to maintain optimal machine use, which is necessary for predictive maintenance. There are three types of condition monitoring: online, periodic, and remote. Finally, remote condition monitoring allows the equipment observed from a small place and data supplied for analysis.

Preventive Maintenance System

To maintain the equipment and materials on a regular basis in order to maintain those running conditions and reduce unnecessary shutdowns due to unexpected equipment failure is called Preventive Maintenance (PM).