Two 8-in-wide wooden boards are to be joined by splice plates that will be fully glued onto the contact surfaces, as shown in the figure. The glue to be used can safely provide a shear strength of 145 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 20,000 lb. Note that a gap of a = 0.4 in. is required between boards (1) and (2). P P (1) (2) Ancwer:

Two 8-in-wide wooden boards are to be joined by splice plates that will be fully glued onto the contact surfaces, as shown in the figure. The glue to be used can safely provide a shear strength of 145 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 20,000 lb. Note that a gap of a = 0.4 in. is required between boards (1) and (2). P P (1) (2) Ancwer:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rivet group connects two narrow lengths of plate, one of which carries a 15 kN load. If the ultimate shear strength t of a rivet is 350 N/mm² and its failure strength in compression stress is 600 N/mm², determine the minimum allowable values of rivet diameter d (mm) and plate thickness t (mm).
The five-bolt connection shown must support an applied load of P = 214 kN. If the average shear stress in the bolts must be limited to 249 MPa, determine the minimum bolt diameter that may be used in the connection.
THe bracket shown is made of cold drawn steel with Sy=400MPa and Su=480 MPa, and is fastened to a beam made of the same material by five rivets that are made of a steel with Sy=300 MPa and Sut=365 MPa. The thickness of the bracket and the beam are 12 mm and 16 mm respectively.Diameters of the rivets are 20 mm. What safe load F(steady) can be supported by the riveted joint for a factor of safety of 2. Use distortion energy theory of failure.
A laminated wood beam consists of eight 2.25 in. × 5.00-in. planks glued together to form a section b = 5.00 in. wide by d = 18 in. deep, as shown. If the allowable strength of the glue in shear is 105 psi, determine(a) the maximum uniformly distributed load w that can be applied over the full length of the beam if the beam is simply supported and has a span of L = 19 ft. [Answer: w = 663.2 lb/ft]
All pins are in double shear, each has a diameter of 13mm, and the average shear stress in each pin is not to exceed 65 MPa. Determine the maximum magnitude P of the loads that the beam can support
The outside diameter of the steel pipe shown is 220 mm and its wall thickness is 6.0 mm. The upper bearing plate has the same width as the reinforced concrete beam it supports. The total load on the column by the reinforced concrete beam is 550 kN. Determine: A. The length L of the rectangular upper bearing plate if its width is 275 mm. and the average bearing stress between the steel plate and the reinforced concrete beam is not to exceed 6.2 MPa.
The lap joint shown is connected by three 16-mm diameter rivets. If the allowable stress for shear in rivets is 40 MPa and bearing between therivets and the plates is 60 MPa determine the safe load P.
A solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the limiting stress of the bar is 27.24 kPa determine the cross sectional area of the steel square bar and its dimensions.
A straight girder of uniform section and length L rests on supports at the ends, and is propped up by a third support in the middle. The weight of the girder and its load is w per unit length. If the central support does not yield, prove that it takes a load equal to (5/8)wL. ANSWER: 1.80cm and 2.48cm Please show solution to the answer.
A stainless steel tube with an outside diameter of 50 mm and a wall thickness of 5 mm is used as a compression member. If the axial stress in the member must be limited to 384 MPa, determine the maximum load P that the member can support.
A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq at an angle of 30 deg with the horizontal. The allowable stresses on the glued joint in tension and shear are 5MPa and 3MPa respectively. Determine the largest load P. Assume that the strength of the glued joint controls the design. The cross-sectional area of the bar is 225 mm^2.
A thrust collar that rests on a 0.75 in thick polymer plate supports the vertical nylon shaft shown below. The shaft has a diameter d = 0.50 in. The load acting acting on the shaft is P = 600lb. A) The ultimate shear strength of the nylon shaft is 2700 psi, and a factor of safety of 2.5 with respect to shear is required. Determine the minimum thickness t required for the thrust collar B) The ultimate bearing strength of the polymer plate is 2000 psi, and a factor of safety of 3.0 with respect to bearing is required. Determine the minimum outer diameter Dcollar required for the thrust collar.