Two masses ma=1.1kg and mp=6.7kg are connected by a rope that hangs over a pulley as shown in the figure. The pulley is a uniform cylinder of radius R=0.39m and mass M=11kg. The system is released from rest. Just before mp hits the ground, calculate the angular speed of the pulley. Take h=4m, g=10 m/s?. Round your answer to one decimal place. CMinder Note: CM MR?. assume the rope is massless and does not slide over the pulley. 2 M

Two masses ma=1.1kg and mp=6.7kg are connected by a rope that hangs over a pulley as shown in the figure. The pulley is a uniform cylinder of radius R=0.39m and mass M=11kg. The system is released from rest. Just before mp hits the ground, calculate the angular speed of the pulley. Take h=4m, g=10 m/s?. Round your answer to one decimal place. CMinder Note: CM MR?. assume the rope is massless and does not slide over the pulley. 2 M

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A small 2-lb ball B is rotating (Fig.13) at angular speed w1 of (6+(0.1*26)) rad/sec about a horizontal shaft. The ball is connected to the bearings with light elastic cords which when unstretched are each 12 in. in length. A force of 15 lb is required to stretch the cord. The distance d1 between the bearings is originally 20 in. If the bearing A is moved to shorten d by 6 in, what is the angular velocity w2 of the ball? Neglect the effects of gravity and the mass of the elastic cords. Use the moment of momentum equation.
The G weight of the figure, when descending, rotates the axis fixed to drums, which are supported by two cylindrical bearings of known dimensions, with known angular velocity ω. Determine the value of weight G, neglecting the rigidity and friction in the rope and assuming that the velocity diagram in the lubricant is linear. Given Data: μ = 8x10⁻² N/m², Di = 0.100 m,D = 0.02 m, Li = 0.1 m,De = 0.101 m, ω = 20/π rd/s
The slender, homogeneous rod shown in the figure below is 3 m in length and has a mass of 12 kg. At the instant shown, the rod has an angle to the horizontal of 60-degrees and an angular velocity of 2 rad/s clockwise. Both walls are smooth and provide negligible friction. At the instant shown, what are the reaction forces at A and B? What is the angular acceleration of the rod's center of mass?
The beam, uniform in mass, M = 47.6 kg and length L = 10.2 m, hangs by a cable supported at point B, and rotates without friction around point A. On the end far of the beam, an object of mass m = 24.3 kg is hanging. The beam is making an angle of θ = 30.9° at point A with respect to the + x-axis. The cable makes an angle φ = 21.1° with respect to the - x-axis at B. Assume ψ = θ + φ. a. Enter an expression for the lever arm for the weight of the beam, lB, about the point A. b. Find an expression for the lever arm for the weight of the mass, lm. c. Write an expression for the magnitude of the torque about point A created by the tension T. Give your answer in terms of the tension T and the other given parameters and trigonometric functions. d. What is the magnitude, in newtons, of the tension in the cable? e. Enter an expression the horizontal component of the force, Sx, that the wall exerts on the beam at point A in terms of the tension T, given parameters, and variables…
Two propellers of lengths and masses l, L and m, M rotate in the same direction, as shown in the figure. If the left propeller starts from rest, w1=0 and the right propeller starts with an angular velocity equal to w2, find the angular velocity with which the right propeller ends up after both propellers have collided.
A motorcycle and rider have a combined mass of 350kg. The each wheel has a mass of 20kg with the diameter of 500 mm. The rider accelerates from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. Identify the magnitude and effect of gyroscopic reaction torque by calculating the angular velocity and power as the motorcycle ascends the incline when the motorcycle and rider travel at 80 km/h around a left-hand bend of road with the radius 30 m.Explain the effects of energy transfer in mechanical systems (e.g. gears, pulley or flywheel) with uniform acceleration present.
- A double-pulley system, as in the right figure above, has masses m1 = 2.00 kg, m2 = 1.20 kg, and m3 = 0.800 kg. (a) What are the accelerations of all the masses? (b) What are the tensions in all the ropes
A counterweight of mass m= 4.10 kg is attached to a light cord that is wound around a pulley as shown in the figure below. The pulley is a thin hoop of radius R = 6.00 cm and mass M = 2.30 kg. The spokes have negligible mass. What is the net torque on the system about the axle of the pulley? When the counterweight has a speed v, the pulley has an angular speed ? = v/R. Determine the magnitude of the total angular momentum of the system about the axle of the pulley. Using your result from (b) and τ = (dL) / (dt), calculate the acceleration of the counterweight. (Enter the magnitude of the acceleration.)
The thin rod in the figure has a mass of 15kg and is attached to a spring of constant k = 50 N / m at one end, which has an unstretched length of 1.5 m. If the rod is released from rest in a horizontal position (ѳ = 0 °) and only conservative forces act on it, determine:a) What is the moment of inertia of the thin rod around the axis of rotation at A? b) What is the angle at which the rod is momentarily at rest again? c) What is the maximum angular velocity of the path?
Two blocks with masses m1 = 5.0 kg and m2 = 7.0 kg are attached by a string as shown in the figure below, over a pulley with mass M = 2.0 kg. The blocks are released from rest. The pulley, which turns on a frictionless axle, is a hollow cylinder with radius 0.050 m over which the string moves without slipping. The horizontal surface is frictionless. Find the speed of the system when the block of mass m2 has dropped 2 m.
In the figure, the hanging object has a mass of m1 = 0.420 kg; the sliding block has a mass of m2 = 0.850 kg, and the pulley is a hollow cylinder with a mass M = 0.350 kg, a interior radius R1 = 0.0200 m and an exterior radius R2 = 0.0300 m. Assume that the mass of the rays is negligible. The coefficient of kinetic friction between the block and the surface horizontal is µk = 0.250. The pulley rotates without friction on its axis. The lightweight cable does not stretch and does not slip on pulley. The block has a velocity of vi = 0.820 m / s towards the pulley when you pass a landmark on the table. (a) Use energetic methods to predict its velocity after it has passed a second point, which is at 0.700 m. (b) Find the angular speed of the pulley at the same moment.
A cylinder of mass M=500kg has an axle of radius b=1m and a spool of radius R=3m. It is placed upright on a table and the string is pulled with a horizontal force F=750N to the right as shown in the figure. The cylinder is rolling without slipping and the coefficient of static friction between the cylinder and the table is µs =0.34. I = 1/2 MR^2a. Determine the linear velocity of the cylinder when it travels a distance D=2m. c. Determine the linear acceleration of the cylinder. d. Determine the friction force acting on the cylinder. e. What is the maximum pulling force, F, for which the cylinder will roll without slipping.