Two single-phase ideal voltage sources are connected by a line of impedance of 0.7 + j2.4 Q as shown in below figure 0.7+ j2.4 N 12 t. 500/16.26° V 58520° V a. source 2 generates active power and receives reactive power b. source 1 receives active power and generates reactive power C. Source 1 generates active power and receives reactive power

Two single-phase ideal voltage sources are connected by a line of impedance of 0.7 + j2.4 Q as shown in below figure 0.7+ j2.4 N 12 t. 500/16.26° V 58520° V a. source 2 generates active power and receives reactive power b. source 1 receives active power and generates reactive power C. Source 1 generates active power and receives reactive power

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

1. Write down a formula for the three-phase power factor, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements. 2. Write down a formula that relates three-phase apparent power to active and reactive power. 3. Draw a graph that depict single-phase waveforms for a purely sinusoidal 50 Hz voltage and a lagging current.
CAN YOU EXPLAIN THE OPERATIONS IN SENTENCES? For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ZLand ZLFind the value of the maximum average power transferred to ?
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
Between the terminals a and b in the figure, there is a load formed by connecting the resistor R0 and inductance L0 in series. The amplitude of the voltage Vs (t) is √2 150 volt phase angle Qs = 0 degree period T = 200π microseconds. Since R = 300ohm and C = 1 microfarad A) If the load phase angle QL = 30 degrees, find the values of R0 and L0 that enable the load to draw the maximum average power from the circuit. =? B) Calculate the average power on the load. =?
In the circuit in the figure, there is a load consisting of the series connection of the resistor R0 and the inductance L0 between the terminals a and b. The amplitude of the VS (t) voltage is √2 150 volts, phase angle = 0 degrees, period T = 200π microseconds.Since R = 300 ohms and C = 1 microfarad a)Find the values of R0 and L0 that enable the load to draw maximum average power from the circuit when the load phase angle is constant at 45 degrees? b)Calculate the average power on the load?
Two impedances Z 1 and Z 2 , when connected separately across a 230 volt, 50 Hz supply consumed 100 watts and 60 watts at power factors of 0.5 lagging and 0.6 leading respectively. If these impedances are connected in parallel across 230 volt, 60 Hz supply, find: (a) total power absorbed and overall power factor; (b) the value of a reactance to be further connected in series with the two to make the overall power factor to be unity.COMPLETE SOLUTION PLEASE
The 9 Ω resistor in the circuit is replaced with a variable impedance Zo. Assume Zo is adjusted for maximum average power transfer to Zo. 1. a) What is the maximum average power that can be delivered toZo?2. b) What is the average power developed by the ideal voltage sourcewhen maximum average power is delivered to Zo?3. c) Choose single components from Appendix H to form animpedance that dissipates average power closest to the value in part(a). Assume the source frequency is 60 Hz.
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
Calculate the impedance ?? for the maximum average power transfer in the circuit shown in Figure 3. and find the value of the maximum average power transferred to.
ZL impedance for maximum average power transfer in the circuit shown in Figure 2and find the value of the maximum average power transferred to the ZL? (Can you write the steps in detail in sentences?)
A non-sinusoidal quasi-square wave voltage v(t) is applied to a nonlinear load, resulting in a non-sinusoidal current i(t). The voltage and current waveforms are shown below. Assume any values of your choice for Vp (≤ 200 V) and Ip (≥ 5 A). 1. calculate the average power and net power factor of the load. 2. The total load harmonic distrotion (THD) of the load current, assuming the smallest frquency term as fundamental.
An industrial installation has a power factor of 0.85 in backward. The demand is 150 KVA, and the operating voltage is 4800 V at 60 Hz. What should be done to bring the power factor to 0.95 in lagging? Indicate what you would connect and with what three-phase power. If the connection of the element to be added is in delta, indicate its reactance and the value of its capacitance or inductance. capacitance or inductance.