Two steel truss members AC and BC, each having cross sectional area of100mm?, are subjected to a horizontal force F as shown in the figure. All thejoints are hinged.459CF600The maximum force F in kN that can be applied at C such that the axial stress inany of the truss members DOES NOT exceed 100MPA is

Answered: Image /qna-images/answer/fd588157-3681-4b05-82f0-2a55e1892e45.jpg

Two steel truss members AC and BC, each having cross sectional area of 100mm?, are subjected to a horizontal force F as shown in the figure. All the joints are hinged. 450 C →F 600 The maximum force F in kN that can be applied at C such that the axial stress in any of the truss members DOES NỘT exceed 100MPA is

Two steel truss members AC and BC, each having cross sectional area of 100mm?, are subjected to a horizontal force F as shown in the figure. All the joints are hinged. 450 C →F 600 The maximum force F in kN that can be applied at C such that the axial stress in any of the truss members DOES NỘT exceed 100MPA is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.6.9P: A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial...

See similar textbooks

Similar questions

, An arm A BC lying in a horizontal plane and supported at A (see figure) is made of two identical solid steel bars AB and BC welded together at a right angle. Each bar is 22 in. long. (a) Knowing that the maximum tensile stress (principal stress) at the top of the bar at support A due solely to the weights of the bars is 1025 psi, determine the diameter d of the bars. (b) If the allowable tensile stress is 1475 psi and each bar has a diameter d = 2.0 in,, what is the maximum downward load P that can be applied at C(in addition to self-weight
The homogeneous bar ABCD shown in figure below is supported by acable that runs from A to B around the smooth peg at E, a vertical cableat C, and a smooth inclined surface at D. Determine the mass of theheaviest bar that can be supported if the stress in each cable is limitedto 100 MPa. The area of the cable AB is 250 mm2 and that of the cableat C is 300 mm2.
Continuous cable ADB runs over a small frictionlesspulley at D to support beam OABC that is partof an entrance canopy for a building (see figure). Assumethat the canopy segment has a weight W =1700 lb.(a) Find the required cross-sectional area of cableADB if the allowable stress is 18 ksi.(b) Determine the required diameter of the pins at O,A, B, and D if the allowable stress in shear is 12 ksi.
A rod is composed of an aluminum section rigidly attached betweensteel and bronze sections, as shown in the figure below. Axial loads areapplied at the positions indicated. If P = 3000 lb and the cross-sectionalarea of the rod is 0.5 in2, determine the stress in each section.
The figure shows 16-mm diameter bolts used to hold two steel plates by fitting inside a cylindrical spacers. Thenormal stress must not to exceed 230 MPa in the bolts and 160 MPa in the spacer. Determine the outer diameterof the spacer.
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa Determine maximum load P for block shear
The circular rods AB and BC is joined at B and fixed at the wall at A, as shown in the figure. Before the load P is applied at B there is a gap between the rods and the wall. LAB =3700 mm, dAB = 26 mm, EAB = 235 GPa, δgap = 10 mm LBC =5700 mm, dBC = 24 mm, EBC = 172 GPa, and P = 75 kN Determine the normal force in BC. Determine the normal stress in BC.
A steam boiler is to have a 300 mm diameter hand placed hole on one end. If themaximum internal pressure is 1.3 MPa, how many 15 mm holes will be required to keepthe cover plate in position? The root diameter of a 15 mm bolt is 12 mm. The allowabletensile stress in the bolts is 100 MPa and the initial stress in the bolts when they aretightened is 600 MPa.
Member AC is shown in Figure is subjected to a vertical force of 3 kN.Determine the position x of this force so that the average compressive stressat the smooth support C is equal to the average tensile stress in the tierod AB. The rod has a cross-sectional area of 400 mm2 and the contact areaat C is 650 mm2.
Two solid cylindrical bars AB and BC are welded at point B and have loads as shown in the figure. If the normal stress cannot exceed 200 MPa on the AB bar and 175 MPa on the BC bar, determine the smallest allowable value for d1 and d2.
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P = 35000 lb and the stress in the steel, aluminum, and bronze sections are limited to 20 ksi, 28 ksi, and 18 ksi, respectively, determine the safest area considering the maximum stress in the aluminum.
@2 The support consists of solid brass post surrounded by a steel tube. Before the load is applied, the gap between these two parts is | mm. Given the dimensions shown in the figure, determine the greatest axial load that can be applied 0 the rigid cap A if the maximum allowable stress in brass is (Guiin)se = 150 MPa and the maximum allowable stress in steel is (Gun ) = 200 MPa. E, = 200 GPa and Ey,= 100GPa.