+ VD -LDw-R3R1V2V1(10 points)V3R2In the circuit above, given V = 6V, V, = 4V, V3 = 1V, R1 = 20, R2 = 4N, R3 = 10, and the turn on voltage ofthe diode is Vah = 0.7V, determine:%3DThe voltage across the diode:Vp =V help (numbers)Then the current through the diode is:Ip =A help (numbers)Note: Be careful about the directions of the voltage sources. Your answers are checked to two decimal places.

Answered: Image /qna-images/answer/3215d4aa-2ec7-4993-8b6b-85d49a5e723a.jpg

+ VD - LD R1 R3 V2 V1 (10 points) V3 ER2 In the circuit above, given V = 6V, V2 = 4V, V3 = 1v, R = 20, R2 = 42, R3 = 1N, and the turn on voltage of the diode is Vih = 0.7V, determine: %3! %3D The voltage across the diode

+ VD - LD R1 R3 V2 V1 (10 points) V3 ER2 In the circuit above, given V = 6V, V2 = 4V, V3 = 1v, R = 20, R2 = 42, R3 = 1N, and the turn on voltage of the diode is Vih = 0.7V, determine: %3! %3D The voltage across the diode

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the ideal-diode clipper circuit given below, VS = 12.sinωt V. Determine the output voltage Vout and sketch this function. Remove the short circuit between points x and y, and replace it with a 2kΩ Resistor. Find the range of values of VS for; D1 and D2 are OFF D1 is ON and D2 is OFF D1 is OFF and D2 is ON Is it possible for both D1 and D2 to be ON?
In your own words(not googled) please answer and help me understand the following a. What is a LED? Explain the working of a LED and give at least two applications. b. Why do LEDs need series current-limiting resistors? c. How does LED differ from an ordinary diode? d. What is a photodiode? Explain how it works and give at least two applications. e. What is a/an: i. Tunnel diode ii. Optoisolator iii. Varactor diode iv. Shockley diode
Apply each of diodeapproximations and determine:a. Current through D1b. Voltage across D2c. Voltage across R3 GIVEN: R1 = 2 kΩ, R2 = 1.2 kΩ, R3 = 6.8 kΩ E= 10 V D1: Si, rB = 2 Ω, rR = 220 kΩ D2: Si, rB = 5 Ω, rR = 560 kΩ DETERMING FIRST IF IT IS A FORWARD BIASED OR REVERSED BIASED THEN, SOLVE IN FIRST APPROXIMATION, SECOND APPROXIMATION AND THIRD APPROXIMATION SHOW THE CIRCUIT DIAGRAM IN EACH APPROXIMATION
R1 = 1 kohms R2 = 1.4 kohms R3 = 6.8 kohms E = 8V D1: Si, rB = 2 ohms, rR = 215 kohms D2: Si, rB = 7 ohms, rR = 590 kohms Apply each of the diode approximations and determine: a) Current through D1 b) Voltage across D_2 c) Voltage across R_3
Since R1=4.51 Kohm, R2=1.19 Kohm R3=2.74Kohm R4=5.60Kohm VCC=23.00V and diode silicon in the circuit given in the figure, find the current passing through the diode in mA
(02) DC Si Diode Circuit. (Course: Electronic Devices and Circuit Theory) What is the minimum value for RL needed to turn Zener diode ON?, And what is the maximum value for RL needed to turn Zener diode is ON? -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.
Given the schematic below, assume D1 and D2 are silicon with forward voltages of 0.7V. Find the following (with solutions) a) Conditions required wherein none of the diodes are conducting b) If both diodes are not conduction, what is Vo? Express in terms of Vi c) Plot the overall relationship of Vo and Vi in the coordinate system shown below. Remember, you are to plot the transfer characteristics of the circuit.
Which of the following ratings (PIV- Peak Inverse Voltage and temperature) is true? A)Si diodes have lower PIV and wider temperature ranges than Ge diodes. B) Si diodes have lower PIV and narrower temperature ranges than Ge diodes. C) Si diodes have higher PIV and narrower temperature ranges than Ge diodes. D) Ge diodes have lower PIV and smaller temperature ranges than Si diodes.
Apply each of diode approximations given the following parameters D`:rB= 2 ohms, rR= 220 kilohms: Si, rB = 5 ohms, rR= 560 kilo ohms Determine the current flowing through D1, D2 AND R2, R3, THE VOLTAGE ACROSS R3 SOLVE IN THREE DIODE APRROXIMATIONS
Analyse the circuit in Figure Q3(a) by using 3 different silicon diode models to determine the value of Vx for each of the models with the aid of suitable diagrams respectively.(Given the forward dynamic resistance, r’d = 10)
Design the network of below to maintain V L at 12 V for a load variation (I L) from 0 mA to 200 mA. That is, determine R S and V Z. Determine P Z max for the Zener diode of part (a).
i) The equation above contains really only three variables in it: Id, Vd, and T. All the other terms are constants. Since in most cases we assume temperature is fairly constant as well, we are really only dealing with two variables: diode current and diode voltage. Based on this realization, re-write the equation as proportionality rather than equality, showing how the two variables of diode current and voltage relate ii) Based on this simplified equation, what would an I vs V graph for a PN junction look like? How does this graph compare against the I vs V graph for a resistor? iii) When "P" and "N" type semiconductor pieces are brought into close contact, free electrons from the "N" piece will rush over to fill holes in the "P" piece, creating a zone on both sides of the contact region devoid of charge carriers. What is this zone called, and what are its electrical characteristics? iv) What happens to the thickness of the region in a PN junction (answer above) when an external…