View Policies Current Attempt in Progress The steel pipe column shown has an outside diameter of 7.875 in. and a wall thickness of 0.25 in. The timber beam is 10.75-in.-wide, and the upper plate has the same width. The load imposed on the column by the timber beam is 80 kips. Determine the average bearing stress at the surfaces between the pipe column and the upper and lower steel bearing plates. Timber beam Concrete slab Steel pipe 9.47 ksi 15.64 ksi 14.66 ksi 13.36 ksi 18.47 ksi 10.75 in.- Save for Later Upper bearing plate Lower bearing plate eTextbook and Media Attempts: 0 of 5 used Submit Answer

View Policies Current Attempt in Progress The steel pipe column shown has an outside diameter of 7.875 in. and a wall thickness of 0.25 in. The timber beam is 10.75-in.-wide, and the upper plate has the same width. The load imposed on the column by the timber beam is 80 kips. Determine the average bearing stress at the surfaces between the pipe column and the upper and lower steel bearing plates. Timber beam Concrete slab Steel pipe 9.47 ksi 15.64 ksi 14.66 ksi 13.36 ksi 18.47 ksi 10.75 in.- Save for Later Upper bearing plate Lower bearing plate eTextbook and Media Attempts: 0 of 5 used Submit Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the Young’s modulus (Y) of the steel rod of 1 m long and a cross sectional area of 0.05 cm2, elongates 2% when supported by a 120 kg load, hung from the other end.
In a small gantry for unloading goods from a railway waggon, it is proposed to carry the lifting tackle on a steel joist, 24 cm by 10 cm, of weight 320 N/m, supported at the ends, and of effective length 5 m. The equivalent dead load on the joist due to the load to be raised is 30 kN, and this may act at any point of the middle 4 m. By considering the fiber stress and the shear, examine whether the joist is suitable. The flanges are 10 cm by 1.2 cm, and the web is 0.75 cm thick. The allowable fiber stress is 1 15 MN/m2, and the allowable shearing stress 75 MN/m2.
A thin copper tube, 14 mm internal diameter and 0,5 mm wall thickness has closed ends and rotates at 1200 r/min while it is subjected to an internal gauge pressure of 222 Pa. Calculate the total hoop stress in the wall of the tube if the density of copper is 8900 kg/m3.
A wood-stave penstock of 1.8 m diameter is wrapped with steel hoops and subjected to a fluid pressure of 380 KPa. If the allowable tension in the hoop is 42.4 kN, what is the maximum hoop spacing?
An aluminum pole for a street light weighs4600 N and supports an arm that weighs 660 N (seefigure). The center of gravity of the arm is 1.2 m from theaxis of the pole. A wind force of 300 N also acts in the (-y)direction at 9 m above the base. The outside diameter ofthe pole (at its base) is 225 mm, and its thickness is 18 mm. Determine the maximum tensile and compressivestresses σt and σc, respectively, in the pole (at its base)due to the weights and the wind force.
A continous wood stave pipe is 3.0 m in diameter and is in service under a head of 30.0 m of water. The staves are secured by means of round 25 mm steel hoops with allowable stress of 105 MPa. Find the masimum spacing in cm of the hoops to safely secure the pipe. Assume that there is an initial tension of 7000 N applied to the hoops.
A tall open-topped standpipe has an inside diameter of 3020 mm and a wall thickness of 8.6 mm. The standpipe contains water, which has a mass density of 1,000 kg/m3.(a) What height h of water will produce a circumferential stress of 18.3 MPa in the wall of the standpipe?(b) What is the axial stress in the wall of the standpipe due to the water pressure?
A retaining wall 6 ft high is constructed ofhorizontal wood planks 2.5 in. thick (actual dimension)that are supported by vertical wood piles of a12 in. diameter (actual dimension), as shown in thefigure. The lateral earth pressure is p1 125 lb/ft2at the top of the wall and p2 =425 lb/ft2 at the bottom.(a) Assuming that the allowable stress in the woodis 1175 psi, calculate the maximum permissiblespacing s of the piles.(b) Find the required diameter of the wood pilesso that piles and planks (t = 2.5 in.) reach theallowable stress at the same time.Hint: Observe that the spacing of the piles may begoverned by the load-carrying capacity of either theplanks or the piles. Consider the piles to act as cantileverbeams subjected to a trapezoidal distribution ofload, and consider the planks to act as simple beams between the piles. To be on the safe side, assume thatthe pressure on the bottom plank is uniform andequal to the maximum pressure.
The doubly-symmetric beam cross section shown in Figure P12.3b has been proposed fora short foot bridge. The cross section will consist of two identical steel pipes that are securelywelded to a steel web plate that has a thickness of t = 9.5 mm. Each pipe has an outside diameterof d = 70 mm and a wall thickness is 5 mm. The distance between the centers of the two pipes ish = 370 mm. Internal forces of P = 13 kN, V = 25 kN, and M = 9 kN·m act in the directionsshown in Figure P12.3a. Determine the stresses acting on horizontal and vertical planes:(a) at point H, which is located at a distance of yH = 120 mm above the z centroidal axis.(b) at point K, which is located at a distance of yK = 80 mm below the z centroidal axis.Show the stresses on a stress element for each point.
The doubly-symmetric beam cross section shown in Figure P12.3b has been proposed fora short foot bridge. The cross section will consist of two identical steel pipes that are securelywelded to a steel web plate that has a thickness of t = 9.5 mm. Each pipe has an outside diameterof d = 70 mm and a wall thickness is 5 mm. The distance between the centers of the two pipes ish = 370 mm. Internal forces of P = 13 kN, V = 25 kN, and M = 9 kN·m act in the directionsshown in Figure P12.3a. Determine the stresses acting on horizontal and vertical planes:(a) at point H, which is located at a distance of yH = 120 mm above the z centroidal axis.(b) at point K, which is located at a distance of yK = 80 mm below the z centroidal axis.Show the stresses on a stress element for each point.FIGURE P12.3a FIGURE P12.3bP12.5 An extruded polymer flexural member is subjected to an internal axial force of P = 580 lb,an internal shear force of V = 420 lb, and an internal bending moment of M = 6,400 lb·in.,…
A fuselage with a perfect circular cross-section with a diameter of 3.6 m and a skin thickness of 1.2 mm. Assume a pressure differential while flying at cruising altitude of 45 kPa. Calculate the circumferential stress induced by the pressure differential
5. In the CN Railwayproject,steel railroad rails of 9.5meters long are to be installed.If the modulus of elasticity of steel is207GPa, and if the lowest temperature considered is 18°C and a maximum temperature of 36°C is designed for, determine the clearance between the rails such that adjoining will just touch at maximum design temperature. Assume α for steel is 11.6 x 10-6/°C