Water is flowing through 150 mm pipe diameter and exist to atmosphere through ahorizontal couple nozzle of 100mm and 75 mm diameter respectively as shown in Figure 2below. If velocity and specific weight of water is 12 m/s and 9.81 kN/m³, respectively,calculate resultant force of water acts on the nozzle junction and its direction. Neglect anylosses into the system100 mm150 mm15030°75 mmV3Figure 2: A pipe junction

Answered: Image /qna-images/answer/6c5485ad-1368-4063-90f4-0c0193b6ba45.jpg

Water is flowing through 150 mm pipe diameter and exist to atmosphere through a horizontal couple nozzle of 100mm and 75 mm diameter respectively as shown in Figure 2 below. If velocity and specific weight of watèr is 12 m/s and 9.81 kN/m³, respeetively, calculate resultant force of water acts on the nozzle junction and its direction. Neglect any losses into the system 100 mm 150 mm 30 75 mm Figure 2: A pipe junction

Water is flowing through 150 mm pipe diameter and exist to atmosphere through a horizontal couple nozzle of 100mm and 75 mm diameter respectively as shown in Figure 2 below. If velocity and specific weight of watèr is 12 m/s and 9.81 kN/m³, respeetively, calculate resultant force of water acts on the nozzle junction and its direction. Neglect any losses into the system 100 mm 150 mm 30 75 mm Figure 2: A pipe junction

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The water enters the sprinkler nozzles with a flow rate of 50 liters / hour in the vertical axis direction and leaves the sprinkler nozzles as 25mm diameter jets and making θ angle with the tangential direction as shown in the figure. The length of the sprinkler arms is 0.45 m. Without considering friction effects; For θ = 75 °, set the rotational speed in rpm.
A vertical pipe of 1 m diameter and 20 m length has a pressure head of 5 m of oil at the upper end. When oil flows through the pipe at an average velocity of 4.5 m/s, the head loss due to friction is 1.6 m of oil. The density of oil is 880 kg/m3 Find the pressure at the lower end of the pipe, when the oil flow is (a) upward direction, (b) downward and also draw the neat sketch. i) Pressure at lower end when flow of oil is upward =________________ N/m2 ii) Pressure at lower end when flow of oil is downward =________________ N/m2
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction ofmotion and leaves it at 150° absolute with the direction of motion. The absolute inletvelocity of the jet is 25 m/s and the vanes move at a velocity of 10 m/s. Ignore frictionacross the vanes. Calculate:1. the hydraulic efficiency.
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.3.1 Find the maximum allowable speed to operate the pump3.2 What power is expected in overcoming friction at this speed, take ƒ = 0.01
In an experiment a jet of water of diameter 20 mm is fired vertically upwards at a sprung target thatdeflects the water at an angle of 120° to the horizontal in all directions. If a 500g mass placed on thetarget balances the force of the jet, what is the discharge of the jet in litre/s?
A Huston turbine impeller with a diameter of 0.217 m is used in a tank with a diameter of 0.65 m filled with liquid to a height of 0.65 m. Four baffles (baffles) are used to avoid vortex, all with a width of 0.01 m. The turbine operates at 275 rpm with a liquid that has a density of 1000 kg/m³ and a viscosity of 0.020Pa.s. a) Considering that the mechanical efficiency is 50%, what is the power in HP of the commercial engine that you should specify?
A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction ofmotion and leaves it at 150° absolute with the direction of motion. The absolute inletvelocity of the jet is 25 m/s and the vanes move at a velocity of 10 m/s. Ignore frictionacross the vanes. Calculate:1. the power/kg of water
6.36 This two-dimensional water (at 50°F) jet is deflected by the two-dimensional vane, which is moving to the right with a speed of 60 ft/s. The initial jet is 0.30 ft thick (vertical dimension), and its speed is 100 ft/s. What power per foot of the jet (normal to the page) is transmitted to the vane? See §6.5 for useful knowledge about moving CVs.
A 2-1/2 inch fire hose discharges water through a nozzle having a jet diameter of 1 inch. Thelost head in the nozzle is 5.76 percent of the velocity head in the jet. If the gage pressure atbase of nozzle is (a) 86 lb per sq in.: (b) 167 lb per sq in.: (1.1) compute the discharge ingallons per minute: (1.2) what is the maximum horizontal range to which the stream can bethrown, neglecting air resistance?
A pipe of diameter 10cm conveying 200 liters/s of water has bend of angle (θ = 90⁰) and θ = 0⁰ through horizontal plane. Find theresultant force exerted on the bend if the pressure at the inlet and outlet of the bend are 15N/cm2 and 10 N/cm2respectively
A vertical pipe of 1 m diameter and 14 m length has a pressure head of 5 m of oil at the upper end. When oil flows through the pipe at an average velocity of 4.5 m/s, the head loss due to friction is 1.8 m of oil. The density of oil is 840 kg/m3 Find the pressure at the lower end of the pipe, when the oil flow is (a) ) Pressure at lower end when flow of oil upward direction (b) ) Pressure at lower end when flow of oil downward and also draw the neat sketch.