When a three-phase short circuit occurs in a 6 kV load busbar, calculate the initial short circuit power if the short circuit impedance is 120 ohms. A)330 KVA B)189 KVA C)345 KVA D)270 KVA E)678 KVA( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).

When a three-phase short circuit occurs in a 6 kV load busbar, calculate the initial short circuit power if the short circuit impedance is 120 ohms. A)330 KVA B)189 KVA C)345 KVA D)270 KVA E)678 KVA( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16MCQ: With generator conyention, where the current leaves the positive terminal of the circuit element, if...

See similar textbooks

Related questions

Q: 1- The impedance of a capacitor increases with increasing frequency. (a) True (b) False 2- If the…

Q: 7 disadvantages of Incandescent Lamps, Tungsten-halogen Lamps, Gaseous Discharge Lamps, and…

Q: can you please elaborate how did u find the cost what does R.H.S after = represents

A: The above question is based on digital circuit design using logic gates.Clarification has been…

Q: 2. Calculate the Fourier transform of the double pulse input function shown in Figure 2. 7 1 f(t) 0…

Q: a 2 b 3 5 d For the given oriented graph, determine fundamental cut-set matrix and express the…

Q: + www R = 60 E = 10 V 20⁰ fs Hz moo L = C=? Where : L = 10 mH, and and the resonant frequency fs =…

Q: Question 9: a- Use Thevenin's theorem to find the voltage and power through R₂ in the following…

A: Given data, , , To find outWe have to determine the voltage and power through , and the maximum…

Q: Find the currents (3) in the following "non-simple circuit V₁-12 V; V2-28 V; V3-22 V, R1-52, R₂-82,…

A: Values of each element is given as,Circuit diagram is given as,

Q: A point charge q is placed at the center of the cavity of a thin metal shell which is neutral. Part…

A: A point charge q is placed at the center of the cavity of a thin metal shell which is neutral.

Q: H.W:Calculate the resonant frequency of the circuit in Fig. Vm cos wt 100 mH -m 0.5 mF 20 Ω

A: circuit

Q: A DC series motor rotates at 1200 rpm and draws 40 A at 240 V. The armature and field resistances…

A: The speed of the motor, The current drawn by the motor,The terminal voltage,The iron and friction…

Q: A rectangular waveguide with a=3 cm and b=5 cm as shown in the figure is filled with polyethylene…

Q: In a Ward-Leonard speed control system, a 1000 kW, 450 V, variable speed motor is driven by a 1500…

A: Armature resistance Supply voltage No load voltage

Q: 5. Simplify the following functions in minimum number of literals. (a) F = xyz + x'y'z+w'xy+wx'y +…

Q: Ipss 12 mA .The supply voltage is -3 V. a) Name the transistor terminals (leads), and the…

Q: A series generator is connected in series to a feeder having 0.522 resistance to boost the voltage.…

A: Given a series generator connected in series with feeder having resistance of The induced voltage,…

Q: The ___________ is the electron deficiency (or holes) at the positive pole of the applied voltage.

A: In case of the electrochemistry and semiconductor physics, There is a anode and cathode, Anode is…

Q: Can you redo it? I need step-by-step solution, like there should be Step 1, Step 2, Step 3, and so…

A: The above question is based on block diagram reduction.

Q: You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 9 to 0…

A: The sequential logic circuit needs to be designed for the given counter sequence and the same can be…

Q: Example. For an air-filled rectangular waveguide with a = 6 cm and b = 3 cm as shown in the figure,…

Q: Determine the voltage (Vo) 4 ΚΩ Μ a 10 ΚΩ

A: Circuit diagram is given as,

Q: 3. a) Consider a single tone message signal m(t) = Am cos(2nfmt) where fm = 30 Hz is the message…

Q: For the following questions, select the best possible answer from the give list 1. True or False:…

A: Given statementsStatement 1:The output current of an OP AMP is zeroHere we need to state whether the…

Q: determine (a) / (n² + n) 2 the z-transform ()n-¹u(n − 1) -

A: Given Data:A discrete-time signal of,To Find:Z-transform

Q: Question 3. Parameters for a 400 V three-phase synchronous generator with 5 kVA power are given as X…

A: The given information about a three-phase star connected synchronous generator is written…

Q: Question 1. Given the Unit Feedback system shown below with G(s)-K/s^3 + 16 s^2 +60s), and…

Q: 1V 17 (4) + عسال 3 por H Wo 10 - ہاں ہر سار Find wood Bwi w ہارج Pseural | 10v2 ) Source /

Q: Design a transformer coupled class A amplifier with high efficiency to supply an output power of P,=…

A: Transformer coupled class A AmplifierIt is a type of electronic amplifier that uses a transformer to…

Q: For the circuit below, what are the output voltage and Amp-Hour measurements at the + and terminals?…

Q: Design a system that has a 15% overshoot and stabilizes in 2 seconds. analyze its absolute stability…

A: The maximum percentage overshoot of the system is 15%.The settling time is 2 seconds.

Q: 3. Determine Vx and Ix: 5mA ΙΚΩ + Vx >1.8KQ2 Ix Si Ge ΙΚΩ 20 V

Q: Design two single-stub (short circuit) shunt tuning networks to match a load impedance ZL-60-j80 2…

A: Solution:Load Impedance =60-j80 (ohm)Load matched =2GHzFind :Here Design Single Stub (short Circuit…

Q: For the feedback circuit in fig(2): What is the F.B. topology Draw the basic amplifier without F.B.…

A: given that feed back amplifier with common emitter current gain…

Q: ircuit shown in Figure 3, the diode cut-in voltage is Vy=0.7 V. Determine vo =+10V and =-10 V. 17 D₁…

Q: Question 2. Given the following feedback system, a. Find the forward transfer function b. What…

A: Here we need to calculate a) forward transfer functionb) system typeC) steady state error for input…

Q: www. 50 ohm C1 2 kohm 2.7 V M TP1 Si

Q: 3. Using branch current method, determine the unknown currents 1₁, 12 and 13 in the circuit given in…

A: Circuit diagram is given as,

Q: In JFET voltage-divider bias, RD=1 kΩ, RS=800 Ω, VP=-4 V, R1=390 kΩ, R2=100 kΩ, VDD=15 V, VGS=-1 V,…

A: In this questionWe need to determine the drain current ID. We knowCurrent in the resistance R, I=…

Q: 2. A simple three-phase power system is shown in the figure below. Assume that the ratings of the…

A: Ratings of devices as,Generator G1: 250 MVA, 13.8 kV. R-0.1 pu, X-1.0 pu.Generator 62: 500 MVA, 20.0…

Q: Find a) capacitance b) Vdc filtered c) Vmax d) Vmin

A: Peak-to-peak ripple voltageSince supply resistance is much less than load resistance, so its effect…

Q: A resistance an inductance of 31.8mH. The circuit is of 7 ohm is connected in series with connected…

A: It is given that:

Q: 12 v 8002 www 1000 A 500, Q/ In the following circuit, find the current, voltage, and capacity, all…

A: it is asked to find the current, voltage and power capacity in all resistors

Q: An air-filled rectangular waveguide is to be constructed for single-mode operation at 15GHz. Specify…

Q: 1- ..the value of path loss that one expects to be exceeded by the actual path loss 50%. 2- Radar…

A: “Since you have posted multiple questions, we will provide the solution only to the first five…

Q: For the following parallel RLC circuit, find the resonant frequency. (Neglect winding resistance).…

Q: Question 1: Flip Flop Consider the following flip flop CLK D C Figl Q Q CLK Vcc J DC K Fig2 1. Give…

A: D FlipflopIt is a flipflop with only 1 input D,also called Delay Flipflop,with eack clock pulse…

Q: Q3.1 Use qualitative analysis to show that the circuit in Figure 3 is a band-reject filter. Q3.2…

Q: A sequential circuit has one primary input m, and one primary output n. It has two D flip-flops with…

Q: point (i.e., Ic and VCE) of the BJT bias circuit please compute the Q- Vcc = 12 V R₁ 56 ΚΩ WW Rc 100…

Q: a) It is desired to draw maximum power by connecting a resistor between a an b. What should be the…

A: In this questionWe need to determine the resistance across the a and b to maximum power delivered to…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

When a three-phase short circuit occurs in a 6 kV load busbar, calculate the initial short circuit power if the short circuit impedance is 120 ohms.

A)330 KVA

B)189 KVA

C)345 KVA

D)270 KVA

E)678 KVA( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given in the question and formula related for solution:

VIEW

Step 2: Solution:

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A balanced Star connected load operates at a voltage of 460V , 0.8 Power factor lagging and each phase takes a power of 8KW. Consider it as 3 - phase 3 - wire system Calculate the total impedance . Calculate the value of Resistance and Inductive Reactance per phase .
A short line having an impedance of (2 + j3) ohm interconnects two power stations A and B both operating at 11kV equal in magnitude and phase. To transfer 25 MW at 0.8 power factor lagging from A to B determine the voltage drop must be compensated by the booster so that the voltages are maintain the same at both ends.
A three-phase overhead line has a load of 30MW, the line voltage is 33kV and power factor is 0.85 lagging. The receiving end has a synchronous compensator, 33kV is maintained at both ends of the line. (i)Calculate the MVAr of the compensator given that the line resistance is 6.5Ω per phase and inductance reactance is 39Ωper phase. (ii)Repeat your calculation using the short-circuit current at node method. Compare and explain the difference between the results.
A single phase transmission line is delivering 480 kVA load at 14 kV. Its resistance is 4 Ω and inductive reactance is 8 Ω if the load power factor is 0.9 lagging. Determine the Current through the line Answer for part 1 Sending end voltage Answer for part 2 Sending end power factor Answer for part 3 Regulation of transmission line Answer for part 4 Efficiency of transmission line
It is standard practice to describe the phase sequence in terms of the line voltages even though the line and phase voltages of a delta-connected system are the same. True False
A single phase transmission line is delivering 460 kVA load at 10 kV. Its resistance is 6 Ω and inductive reactance is 6 Ω if the load power factor is 0.7 lagging. Determine the Current through the line Answer for part 1 Sending end voltage Answer for part 2 Sending end power factor Answer for part 3 Regulation of transmission line Answer for part 4 Efficiency of transmission line Answer for part 5
With generator conyention, where the current leaves the positive terminal of the circuit element, if P is positive then positive real power is delivered. (a) False (b) True
Provide a design for a three-phase D-Y grounded (150MVA, 34.5kV/345kV) transformer protection by using 87 mechanical relay.
The power system insulation problem involves a. Capacitance of earth and subsequent grounding b. Selection of basic insulation level of system equipment c. Determination of single phase line insulation d. Determination of three phase line insulation Clear my choice
2. For a 3-phase, 4-wire system having balanced supply and unbalanced load, the following sequence components are obtained: I1=200∠0° A, I2=100∠60° A°. If the Neutral current is equal to 300∠300° A.a. Ia, Ib, Icb. I0
Draw the single line diagram of a substation having the following equipments:i) Incoming lines: Two, 132kVii) Outgoing lines: (a) Five, 132kV (b) Five, 33kViii) Transformers: (a) One, 25MVA, 132/33kV, D/Y (b) One, 2MVA, 33kV/ 420V,Y/Yiv) Bus-bars: 132 kV-Duplicate bus-bar, 33kV single bus-barShow the positions of necessary equipments that using for protections, measurements and communications.
A minimum of three wattemer should be used to measure power for a three phase balanced system. True False