Which claim is correct? A transfer function model for a stable process always has no time-delay. Feedforward control can be solely used for the setpoint tracking If a process has 3 inputs and 3 outputs, then we need to build 6 transfer function models for it. The inner loop of cascade control has to be slower than the outer loop No correct answer

Which claim is correct? A transfer function model for a stable process always has no time-delay. Feedforward control can be solely used for the setpoint tracking If a process has 3 inputs and 3 outputs, then we need to build 6 transfer function models for it. The inner loop of cascade control has to be slower than the outer loop No correct answer

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter54: The Operational Amplifier

Section: Chapter Questions

Problem 7RQ: Name two effects of negative feedback.

See similar textbooks

Similar questions

1. Give an example of open loop and closed loop system (one example each). Also state the input, control system, feedback and output parameter. Example. 1. Open Loop - Water Heater: Input - Water Temperature (Cold) System - Heating Element Output - Water Temperature (Hot) 2. Closed Loop - Air-conditioning System Input - Desired Room Temperature Control - Motor controller/Compressor/ACU Feedback - Temperature Sensing Output - Room Temperature
a)is the aircraft stable about the equilibrium represented by the transfer function? b) Using proportional feedback,what is the range of acceptable gains for the closed loop systen to be stable? c) Design a feedback control system that allows the pilot to command a pitch angle with overshoot less than or equal to 4.15% and a natural frequency of greater than or equal to 0.99 rad/s d) Design a feedback control system that allows the pilot to command a pitch angle with the same overshoot and a natural frequency of one half the system in part c.
EXPERIMENT TITLE : PID CONTROLLER IN LEVEL CONTROL SYSTEM OBJECTIVE:To demonstrate the characteristic of P,PI and PID controller response on a level controller system. Based on the topic and objective given,please make a clear introduction.
LESSON is Transfer Function: Mechanical System - Rotational Movement SUBJECT: FEEDBACK CONTROL SYSTEM Box the final answer
Example 1.1 Figure 1.5 shows the block diagram of a closed-loop flow control system. Identify the following elements: (a) the sensor, (b) the transducer, (c) the actuator, (d) the transmitter, (e) the controller, (f) the manipulated variable, and (g) the measured variable. In the figure above, the (a) sensor is labeled as the pressure cell. The (b) transducer is labeled as the converter. However, there are two converters: one for converting pressure to current, and another converting current to pressure for operating the actuator. The (c) actuator is labeled as the pneumatic valve. The (d) transmitter is labeled as the line driver. The (e) controller is labeled as the PLC. The (f) manipulated variable is labeled as the pressure developed by the fluid flowing through the orifice plate. The (g) measured variable is the flow rate of the liquid.
(PID solution with the requirements and simple explanation. Thx) INSTRUCTION: Given three bare processes develop a control system using feedbackand feedforward concept/principle. Your output is a process and instrumentationdiagram (P & ID) using ISA's Instrument Identification and Symbols standards withexplanation. PROCESS 2: The liquid level inside the tank is regulated at a value of 3.0 m on a condition ofcontinuous liquid inflow and outflow. Requirements: Two feedback solutions One feedforward solution
A proportional controller is used to control the height of water in a tank where the water level can vary from 0 to 4.0 m. The required height of water is and the controller is to close a valve fully when the water rises to 3.9 and open it fully when the water falls to 3.1 m. What transfer function will be required? source : Mechatronics: Electronic Control Systems in Mechanical and Electrical Engineering 6th Edition by W. Bolton question 22.4
TIME DOMAIN MODELING AND RESPONSE FOR CONTROL SYSTEMS
Calculating the separation and / or joining angles in the negative feedback control circuit, if any, given as Controlling (K) and Controlled G (s) = (s + 1) / (s2-4 * s + 5) Explanation: The roots of the equation (s2-4 * s + 5); s1 = 2 + 1 * j and s2 = 2-1 * j and the system Transfer Function is TF (s) = K * G (s) / (1 + K * G (s)). a. There are split angles up to (+108.435) and (-108.435) b. There are split angles as much as (+71,565) and (-71,565) c. There are conjunction angles of (+90) and (-90). D. There are separation angles as much as (+18.435) and (-18.435). E. There are no separation and convergence angles.
In the mid-1900s, several technological and analysis concepts came together to make the PID controller widely accepted as an effective industrial controller. Discuss in detail and evaluate the performance of a PID or three-term controllers that are widely used in a typical paper mill where there may be about 2000 control loops, and over 90% of these would be PID control loops.
How do you interpret a continuously rising or falling angular position output in Simulink
One of the disadvantage of negative feedback loop is lag caused because it can only be exerted after controlled variable has been disturbed. In order to minimize lag between a change in a controlled variable and the action of the effector, it is advantageous for the body to anticipate any likely change. Which one of the following physiological mechanism achieves this? Select one: a. Feedbackward control b. Feedforward control c.Positive feedback control d. All of the above e. None of the above