while flowing through a smooth pipe with 1.5 cm inner diameter and 7 meters length.The entire surface of the pipe is equipped with an electric heater, which ensures uniform heating throughout.The outer surface of the heater is well insulated and therefore all heat generated in the heater in continuous operation is transferred to the water in the pipe.If the system provides 6 Liter / minute flow rate of hot water. (Thermophysical properties of water at 50 oC:ρ = 988 m3/kg, k= 0.6305 W/m oC, cp=4181 J/kg oC, Pr=3.628, μ= 0.0005471 kg/m.s ) a)Find the power of the resistance heater [W]. b)Calculate the inner surface temperature [oC] of the pipe at the outlet. c)Find the pressure drop [Pa].

while flowing through a smooth pipe with 1.5 cm inner diameter and 7 meters length.The entire surface of the pipe is equipped with an electric heater, which ensures uniform heating throughout.The outer surface of the heater is well insulated and therefore all heat generated in the heater in continuous operation is transferred to the water in the pipe.If the system provides 6 Liter / minute flow rate of hot water. (Thermophysical properties of water at 50 oC:ρ = 988 m3/kg, k= 0.6305 W/m oC, cp=4181 J/kg oC, Pr=3.628, μ= 0.0005471 kg/m.s ) a)Find the power of the resistance heater [W]. b)Calculate the inner surface temperature [oC] of the pipe at the outlet. c)Find the pressure drop [Pa].

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.9P

See similar textbooks

Similar questions

Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID, 60-cm-long copper tube at a velocity of 0.03 m/s. The oil enters the tube at 16C, and the tube is heated by steam condensing on its outer surface at atmospheric pressure with a heat transfer coefficient of 11.3 kW/m K. The properties of the oil at various temperatures are listed in the following table: Temperature, T(C) 15 30 40 65 100 (kg/m3) 912 912 896 880 864 c(kJ/kgK) 1.80 1.84 1.925 2.0 2.135 k(W/mK) 0.133 0.133 0.131 0.129 0.128 (kg/ms) 0.089 0.0414 0.023 0.00786 0.0033 Pr 1204 573 338 122 55
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
Determine the rate of heat transfer per meter length from a 5-cm-OD pipe at 150C placed eccentrically within a larger cylinder of 85 magnesia wool as shown in the sketch. The outside diameter of the larger cylinder is 15 cm and the surface temperature is 50C.
A mild-steel cylindrical billet 25 cm in diameter is to be raised to a minimum temperature of 760C by passing it through a 6-m long strip-type furnace. If the furnace gases are at 1538C and the overall heat transfer coefficient on the outside of the billet is 68W/m2K, determine the maximum speed at which a continuous billet entering at 204C can travel through the furnace.
7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
A spherical communications satellite, 2 m in diameter, is placed in orbit around the earth. The satellite generates 1000 W of internal power from a small nuclear generator. If the surface of the satellite has an emittance of 0.3, and is shaded from solar radiation by the earth, estimate its surface temperature.
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a well-insulated 40-L tank of water that is initially at 300 K. If each heater dissipates 500 W, what is the time required for bringing the water temperature in the tank to 340 K? State your assumption for your analysis.