- Write an assembly code to check if a number is falling within the range j...k (inclusive). Ask the user to enter both ranges j, K and the number num you want to check. Output the suitable message based on the situation Within the range Outside the range Always prompt the user to enter a value using a suitable message. For example (multiple runs) Enter J - beginning of the range: 3 Enter K – end of the range: 15 Enter the value you want to check: 6 6 is within the range 3 to 15 Enter J - beginning of the range: 6 Enter K– end of the range: 15 Enter the value you want to check: 6 6 is within the range 6 to 15

in mips Write a program that asks the user to enter a signed number and read it. Then display the content of multiplying this number by 37.25. Note1: Only the shift instructions are allowed (No mul/div) in this task. Note2: Anything after decimal point in the result is ignored. foucs on notes please

Write in pseudo-code a program/algorithm that takes a number on the input and expresses all the different ways the input can be represented as the sum of 1,3 and 4 simultaneously.  This question does not ask for the COUNT but rather the various solutions.

Write pseudocode to solve the following problem. Must use iterative dynamic programming (tabulation) and run in O(n) time. Input: positive integer n Output: two non-negative integer x and y where n = x185 + y120 Example: if n=1230 then x=6 and y=1 (1314 = 6(185) + 1(120))

C++input n,output： 1 12 123 .... 123....n example： n = 3 1 12 123   n= 5 1 12 123 1234 12345

Please use C++ In this lab, you need to write a program which, given a seven digit binary input given below, it will check to see if there is a single bit error using the Hamming Code method discussed in lab. For a sample of Hamming Code, the input: 1110101 will reveal that ‘110’ is the location of the error (meaning the sixth slot in the input), so the corrected number would be 1010101, and the actual message transmitted, would be 1011, which is 11 in decimal. You can use this example to test your program to ensure it’s working correctly. Create a program which can, given a 7-bit long input, written in Hamming Code style, do the three following tasks, displaying the results as output.             (1) Determine if there’s an incorrect bit, and if so, where it is.             (2) Display what the CORRECT code should look like (if it needs to be corrected.)             (3) Display the decimal form of the message that was sent, after any needed correction. Remember, when using Hamming…

write a code that decodes the coloured bands on a resistor.Each colour band printed on a resistor has a corresponding numeric value, as shown in the table below: Colour Numeric value black 0 brown 1 red 2 orange 3 yellow 4 green 5 blue 6 violet 7 grey 8 white 9 To calculate the total resistance value, the following formula should be used: resistance=(10a+b)⋅10^c where a, b, and c are the numeric values of the first, second, and third colour bands respectively. For example, let's say that the colour bands on a resistor are red-green-orange. In this case, a=2, b=5, and c=3 (using the table). Hence the resistance value is 25000 ohms: resistance=(10*2+5)⋅10^3=25000 ohms Your task is to write a program which asks the user to input the three colour bands. The program should then calculate and output the resistance value indicated by the bands. As part of your solution, you must define and use a function named colour_to_number. This function should take one…

use c++

Please help write this in verilog

Using the switch function, Write a C program that takes 2 Integers from the user and does a mathematical operation to the two values based on the case input:            Case -1: Addition             Case -2 : Subtraction             Case -3: Multiplication             Case -4: Division *All Variables types to be float *Add a default message: (“Invalid input, Insert 1,2,3 or 4)