A steel wire 60cm long and 0.32 cm in -9 radius is attached to the pulley in 5.5cm radius , 3kg weight is attached to the end of the pulley caused to twist the free end of the wire to an angle with magnitude of about 10 ,calculate the rigidity coefficient * (n) ?Assume the g=980cm/s2

A steel wire 60cm long and 0.32 cm in -9 radius is attached to the pulley in 5.5cm radius , 3kg weight is attached to the end of the pulley caused to twist the free end of the wire to an angle with magnitude of about 10 ,calculate the rigidity coefficient * (n) ?Assume the g=980cm/s2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.5.2P: A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is...

See similar textbooks

Related questions

Q: A laminated spring 1 m long is made up of plates, each 5 cm wide and 1 cm thick. If the bending…

A: We know that a 1 m long laminated spring is made up of plates that are each 5 cm broad and 1 cm…

Q: A thin steel tire is shrunk on to a locomotive wheel of 1.2 m diameter. Find the internal diameter…

A: GIVEN DATA DIAMETER D=1.2m =1200mm HOOP STRESS =100MPa E=200KN/mm2 α=6.5*10-6/'C We have to find…

Q: Consider a hollow steel shaft with a 130mm outside diameter and a 70mm inside diameter. What is the…

A: Given Data⇒ Hollow steel shaft Outside diameter of shaft(D)=130 mm=0.13 m Inside diameter of…

Q: A hollow shaft with external and internal diameters 100 mm and 75 mm respectively transmits 500 kW…

A: As per given question calculate the shear strain at the inner and outer radii and the modulus of…

Q: A solid cylindrical metal of 130 cm tall and 30 mm thick is centrally bored for 0.3 m, the bore…

Q: The axis of a tree has the following data, the diameter d= 40mm and the length is L= 0.9m and it…

Q: The rotation in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 10 mm in radius and…

A: Given: The shaft length, L = 800 mm = 0.8 m The torque applied, T = 80 N.m The radius of shaft, r =…

Q: Solid steel wrench (shown in Fig. 4) has a radius of 0.4 cm. and a length of 0.2 m. What is the…

A: Given, diameter of the wrench , d=2×0.4 cm=0.8 cm=8 mm Length, L=200 mm Allowable shear stress,…

Q: A cantilever of circular cross section has a diameter of 150 mm and is made from steel, which, when…

Q: A close coiled helical spring that is made of a material with a shear modulus of 150 GPa, has a wire…

Q: Solid steel wrench (shown in Fig. 4) has a radius of 0.4 cm. and a length of 0.2 m. What is the…

A: Given The radius of steel wrench is r=0.4 cm. The length of steel wrench is l=0.200 m. The…

Q: rectangular bar 40 mm wide and 30 mm thick is 0.5 m long. It is acted upon by axial tensile force of…

Q: A 12-mm thick steel tire has a width of 110 mm and internal diameter of 800 mm. It is heated and…

Q: 10 A flat spiral spring is 12 mm wide, 0.3 mm thick and 2.5 m long. Assuming the maximum stress of…

A: A flat spring is 12 mm wide, 0.3 mm thick, and 2.5 m long, as far as we know.The maximum stress of…

Q: A plat spiral spring is made of 6 mm wide.and 2.5 mm thick wire andis 250 cm long. Assuming the…

A: Given data: width of spring = 6 mm Thickness of wire = 2.5 mm length = 250 cm Maximum stress = 840…

Q: 3. A cylindrical metal rod of 50mm diameter and 3m length is subjected to a tensile load of 150KN.…

A: Strain is the deformation in the material per unit length. True strain is the natural log of the…

Q: A stepped steel shaft shown below is subjecte to 10 N-m torque. If the moduius of rigidity 80 GPa,…

A: Given:Torque, T=10 N-mG=80 GPad1=50 mmd2=25 mmL=100 mm

Q: A laminated steel spring, simply supported at the ends centrally loaded, with a span of 75 cm is…

A: Springs are one of the flexible machine elements, which gets deformed when load is applied to it and…

Q: 15 mm diameter shaft rotates in long fixed bearings 60 cm apart. A rotor of mass 20 kg is mounted at…

A: Given: The diameter of shaft, d = 15 mm The length of shaft, L = 60 cm The mass of rotor, m = 20 kg…

Q: A shaft capable of transmitting 50 kW of power will spin at 100 revolutions per minute. The maximum…

A: Given Power, P = 50 kW Speed, N =10 0 rpm Length, l = 3 m Angle = 1.5 degree Find Diameter,…

Q: What is the Poisson's ratio if the ratio of Young's modulus (E) to the shear modulus (G) is 2?

A: Given data, The ratio of young's modulus and shear modulus is 2 ie E/G=2

Q: The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in…

Q: A thin metal pipe of mean radius R, thickness t and length L, has its ends closed and is full of…

A: given data,Mean radius=RThickness=tLength=L

Q: 4) A sophisticated machinery design has a flat bar fillet component with a thickness of 10mm. For an…

Q: A link of a valve gear has to be curved in one plane, for the sake of clearance. Estimate the…

Q: A bar is subjected to fluctuating tensile load from 20 kN to 100 kN .The material has yield strength…

Q: The rim of a steel flywheel 1 m diameter and 200 mm wide is rotating at 2400 rpm. Calculate: (a) The…

Q: estimate the maximum central deflection before the yield stress

A: Given L=0.6 m cross section=15 mm x 5 mm yield stress= 300 MPa E=200 GPa To determine: The maximum…

Q: A 100 cm long shaft with a load of 2000 N in the middle is 25 KW powerful. It is driven by a motor…

Q: What is the magnitude of shear stress generated in shaft of diameter 20 mm when 10 Nm torque is…

Q: A helical spring having squared and ground ends has a total of 20 coils and its material has modulus…

Q: (a) What is spring ? Briefly define the type of spring. Also explain the formula of stress for flat…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: A hollow 3 m long steel shaft that will provide the main engine drive transmission for a ship to be…

A: Given data: Length of hollow steel shaft, L=3 m=3000 mm. Torque requirement is, T=25 kN.m=25×106…

Q: A steel bar of 50mm wide, 12mm thick and 300mm long is subjected to an axial pull of 84KN. Find the…

Q: Consider a hollow steel shaft with a 130 mm outside diameter and a 70 mm inside diameter. What is…

Q: A bar is subjected to fluctuating tensile load from 20 kN to 100 kN .The material has yield strength…

A: Given: The fluctuating tensile load in a bar,P1=20 kNP2=100 kNσyt=240 MPaσe=160 MPaFactor of safety,…

Q: A simple diagram of a driveshaft ABC is shown in Figure 3. The power generated by an engine is…

Q: A short rectangular-sectioned timber post has one side of its section twice the other. When 9.542 kN…

A: The elongation/contraction of a rectangular beam subjected to a axial load can be calculated using…

Q: uter diameter 60 mm and inner diameter 40 mm) is running at 43 Hz. If the shaft transmits 156 kW,…

Q: 2. The discs in the spinal column can withstand a stress (force per unit area) of 1.1 x 107 N/m2…

A: GIVEN: σ=1.1X107 N/m2A=10cm2=10-3m2 a) Maximum force that can be applied before rupture takes…

Q: A circular rod of diameter 16 mm and 500 mm long is subjected to a tensile force 40kN. The modulus…

A: Given, The diameter of the rod, d=16 mm The length of the rod, L=500 mm The load, P=40 kN=40000 N…

Q: Young's modulus for the material of a substance is 7.25 x 1010 N.m-2 and its bulk modulus is 11 x…

A: Given data : Youngs modulus=EBulk modulus=KTo find :Poisson ratio

Q: A windmill turns a series of slender rods fixed about one end (see formula below). They are…

Q: A bar is subjected to fluctuating tensile load from 20 KN to 100 kN. The material has yield strength…

A: Given, Minimum force during a cycle = Fmin = 20 kN Maximum force during a cycle = Fmax = 100 kN…

Q: A bar is subjected to fluctuating tensile load from 20 kN to 100 kN. The material has yield strength…

A: Given, Minimum tensile load = Fmin = 20 kN = 20,000 N Maximum tensile load = Fmax = 100 kN = 100,000…

Question

A steel wire 60cm long and 0.32 cm in -9
radius is attached to the pulley in 5.5cm
radius , 3kg weight is attached to the end of
the pulley caused to twist the free end of
the wire to an angle with magnitude of
about 10 ,calculate the rigidity coefficient
* (n) ?Assume the g=980cm/s2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

carbon tetrachloride at 20 degree celcius has a viscosity of .00097 kg/m.s. what shear stress required to deform this fluid at a strain rate of 5000 Hz?
A cable is tied to a car, which then speeds away. The car and the object to which the cable is tied are considered rigid. The car weighs 3000 lbs. The cable is 100 ft long and has an area of 0.2 in2. If the car is going 5 mph when it reaches the end of the cable, calculate (i) deflectionin the cable, (ii) Stress in the cable, (iii) Max. force in the cable. (Ecable = 12 × 106 psi)
A 100 × 50 × 25mm steel block is subjected to a hydrostatic pressure of 5 MPa. The Young's modulus and Poisson's ratio of the material are 150GPa nd 0.2 respectively. The change in the volume of the block in mm³ is
A thick-wall underwater pipe is placed at 20m below sea level. The pipe is carryingcompressed natural gas with pressure of 50 MPa. The pipe has 115mm outer diameter andmade of 316 stainless steel with yield strength of 205 MPa. The density of sea water could betaken as 1029 kg/m3. Find out:a) What is the resultant outer pressure acting on the underwater pipe? b) What is the minimum inner diameter to ensure the pipe does not yield?c) Sketch the variation of hoop and radial stress across the pipe wall, completed with stresslabelling. d) What is the resultant longitudinal stress of the pipe?
specimen of oil having an initial volume of 600 cm3 is subjected toa pressure increase of 3.6 x 106Pa and the volume is found todecrease by 0.45 cm3. What is the bulk modulus of the material?
A cube with edges of length L = 0.23 m and density ρc = 3.4×103 kg/m3 is totally submerged in water, with a density of ρw = 1.00×103 kg/m3, and oil, with a density of ρo = 0.82×103 kg/m3, as shown in the figure. The cube is submerged in the water to a depth of d = 0.065 m, while the rest of the cube is in oil. The cube is suspended by a taut string and is in static equilibrium. a) Calculate the magnitude of the buoyant force, in newtons. b) Enter an expression for the tension in the string, in terms of the defined quantities and g.
A cube with edges of length L = 0.19 m and density ρc = 2.8×103 kg/m3 is totally submerged in water, with a density of ρw = 1.00×103 kg/m3, and oil, with a density of ρo = 0.93×103 kg/m3, as shown in the figure. The cube is submerged in the water to a depth of d = 0.055 m, while the rest of the cube is in oil. The cube is suspended by a taut string and is in static equilibrium. 1) Enter an expression for the magnitude of the buoyant force acting on the cube, in terms of ρw, ρo, L, d, and g. 2) Calculate the magnitude of the buoyant force, in newtons. 3) Enter an expression for the tension in the string, in terms of the defined quantities and g. 4) Calculate the tension in the string, in newtons.
A wood stave pipe, 120 cm in inside diameter, is to resist a maximum water pressure of 1,200 kPa. If the staves are bound by steel flat bands (10 cm by 2.50 cm), find the spacing of the bands if its allowable stress is 105 MPa.\ Please explain the steps and formulas used.
Pressure inside the cylinder is 10 bars Is this a thin walled cylinder when the thickness is 10 mm. Estimate theoretically the hoop andlongitudinal stresses
A tall open-topped standpipe has an inside diameter of 2,750 mm and a wall thickness of 6 mm. The standpipe contains water, which has a mass density of 1,000 kg/m3 . (a) What height h of water will produce a circumferential stress of 16 MPa in the wall of the standpipe? (b) What is the longitudinal stress in the wall of the standpipe due to the water pressure?
The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.
1. A solid piece of metal of volume 10,000 mm3 is compressed by a pressure of 70 MPa. Determine the bulk modulus given that the Young’s modulus E is 214 Gpa and the Poisson’s ratio is 0.33. Also determine the change in the volume.2. Starting from the first principles derive the relation between Young’s modulus (E), shear modulus (G) and Poisson’s ratio (υ)