You now wish to see how much each experimental value obtained above differs from the actual or accepted value. You therefore decide to find the percent error using the equation you also learned: Substitute the following values in the above equation and calculate the two percent error values. E1 9.96 m/s2 E2 9.72 m/s2 A 9.80 m/s2 Percent error for E1___ Percent error for E2____

You now wish to see how much each experimental value obtained above differs from the actual or accepted value. You therefore decide to find the percent error using the equation you also learned: Substitute the following values in the above equation and calculate the two percent error values. E1 9.96 m/s2 E2 9.72 m/s2 A 9.80 m/s2 Percent error for E1_ Percent error for E2__

Chemistry & Chemical Reactivity

9th Edition

ISBN:9781133949640

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

ChapterL: Let's Review

SectionL.2: Making Measurements: Precision, Accuracy, Experimental Error, And Standard Deviation

Problem 1RC

See similar textbooks

Similar questions

The percentage of an additive in gasoline was measured six times with the following results: 0.13; 0.12; 0.16; 0.17; 0.20 and 0.11%. What is the 99% confidence interval for the additive percentage?
Substance Melting Points in ℃ Benzoic acid 122.3 ℃ Succinimide 125-127 Urea 133 ℃ Cinnamic acid (trans). 133 ℃ Thiourea 182 ℃ Hippuric acid. 187 ℃ For Questions 1-3 assume that you were given 5.00 g of an unknown A for this lab, one of the six compounds whose melting points you looked up for prelab. 1. You recrystallized A and obtained 2.23 g pure product. What was your percent recovery? That is, what percent of the original mass did you get back? Show your work. 2. Assume you took the melting point of the pure product and it was 123oC. Considering…
1. Calculate the experimental density of a salt solution and the percent error (same as relative error percent) using some or all the data given below. solubility of NaCl salt in water: 0.357 g/mLmass of empty graduated cylinder: 25.19g mass of graduated cylinder + salt solution: 30.47g total volume of salt solution: 4.98 mLtrue density of salt solution: 1.07 g/mL
You have a stock solution certified by a manufacturer to contain 245.0±0.2 ?g SO2−4/mL. You would like to dilute it by a factor of 100 to obtain 2.450 ?g/mL. Two possible methods of dilution are stated. For each method, calculate the resulting absolute uncertainty in concentration. Use the manufacturer's tolerances in the table for uncertainties. Glassware Tolerance 1‑mL transfer pipet ±0.006 mL±0.006 mL 10‑mL transfer pipet ±0.02 mL±0.02 mL 100‑mL volumetric flask ±0.08 mL±0.08 mL Method A: Dilute 10.00 mL up to 100mL with a transfer pipet and volumetric flask. Then take 10.00 mL of the dilute solution and dilute it again to 100 mL. absolute uncertainty: ±.-----?g/mL Method B: Dilute 1.000 mL up to 100 mL with a transfer pipet and volumetric flask. absolute uncertainty: ±------?g/mL
Analysis was run on samples from a known CRM with 8.85% Fe. The following results for %Fe were obtained by an analyst: 8.75, 8.51, 8.25, 8.61. Which of the following statements is true assuming none of the data points are outliers? Group of answer choices Tcalc = 63.15 The analysis is not accurate at the 95% confidence interval. Tcalc = 3.03 The analysis is accurate at the 95% confidence interval. Not enough information to determine Tcalc = 63.15 The analysis is accurate at the 95% confidence interval. Tcalc = 3.03 The analysis is not accurate at the 95% confidence interval.
Q3 we dilute unknown sample of 25ml to 100ml And want to find error propagation associated with it. The unknown sample concentration is :1.2984 ppm Error: .1958 Class A 25 ml pipet error : .03ml Class A 100ml beaker : .08 I find the unknown concentration but need error associated with it during dilution process Any hints?
(8) Identify whether the following are examples of systematic or random error or are mistakes: a. Using an inaccurately calibrated buret. b. An uncertainty of 1 mg in the weight of your sample.∓ c. Overshooting the endpoint on your first sample, then hitting the endpoint on the remaining samples.d. Failing to let your volumetric pipet drain for a few seconds have most of the liquid has been delivered.
A method to determine an antibiotic was developed and validated in a pharmaceutical company. The method allows analysis of 100 mg tablets containing 7.5 mg of the antibiotic. According to the validation data, the confidence limits are 7.50 mg± 0.04mg. How many samples will need to be analyzed for an analyst to ensure that the content of the antibiotic in a macerated sample of that drug is 7.50 mg ± 0.03 mg with 95% reliability when analyzing 100 mg of the macerated sample?
Which is an example of an indeterminate error? Wrong dilution of sample solution Overshooting endpoint Wrong calibration solution used Fluctuation in the reading of balance
Two aqueous hydrogen bromide solutions containing 1.00 wt% HBr (SG=1.0041) and 60.0 wt% HBr (SG=1.6731) are mixed to form a 3.54 M HBr solution (SG=1.1935). What feed rate of the 60.0 wt% HBr solution would be required to produce 1350 kg/hr of product?
A certified reference material of lead in calcium carbonate is analyzed by a laboratory and found to have a lead content of 237 ng/g.237 ng/g. The reported certified value for this material is 211 ng/g.211 ng/g. What is the absolute error and the percent relative error for the method used in this analysis? absolute error: percent relative error:
7. A procedure for measuring the amount of creatinine in blood was applied to a standard blood sample and the following results were produced: 0.787, 0.812, 0.796, 0.739, 0.802, and 0.823 mg/dL. a) Can any of the data points be rejected by the Grubbs test? b) What is the 95% confidence interval for the data?