Analysis was run on samples from a known CRM with 8.85% Fe. The following results for %Fe were obtained by an analyst: 8.75, 8.51, 8.25, 8.61. Which of the following statements is true assuming none of the data points are outliers? Group of answer choices Tcalc = 63.15 The analysis is not accurate at the 95% confidence interval. Tcalc = 3.03 The analysis is accurate at the 95% confidence interval. Not enough information to determine Tcalc = 63.15 The analysis is accurate at the 95% confidence interval. Tcalc = 3.03 The analysis is not accurate at the 95% confidence interval.

Analysis was run on samples from a known CRM with 8.85% Fe. The following results for %Fe were obtained by an analyst: 8.75, 8.51, 8.25, 8.61. Which of the following statements is true assuming none of the data points are outliers? Group of answer choices Tcalc = 63.15 The analysis is not accurate at the 95% confidence interval. Tcalc = 3.03 The analysis is accurate at the 95% confidence interval. Not enough information to determine Tcalc = 63.15 The analysis is accurate at the 95% confidence interval. Tcalc = 3.03 The analysis is not accurate at the 95% confidence interval.

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter3: Statistical Tests With Excel

Section: Chapter Questions

Problem 2P

See similar textbooks

Similar questions

An analysis of city drinking water for total hardness was done by two students in the laboratory and produced the following results (in ppm CaCO3): Student A: 228.3, 226.4, 226.9, 227.1, and 228.6. Student B: 229.5, 226.1, 230.7, 223.8, and 227.5What is the 95% confidence interval for the mean?
Explain the use of plans and their importance in assessing the quality of pharmaceutical products. Provide a step-by-step design of a sampling plan based on a normal inspection for a 75,000 tablets with an AQL of 0.12% using the attached table (at the end of exam paper).
A chemist working in a hospital clinical laboratory obtained the following values for uric acid in blood serum: 4.63, 4.58, 4.82, 4.31, 4.67 and 4.60 mg%. What value should be reported as the mean? Value of QT at 90 % confidence level is 0.56.
You determine the acetic acid (HOAc) content of vinegar by titrating with a sodium hydroxide standard solution to a phenolphthalein (an indicator) end point. An approximately 5-mL sample of vinegar is weighed on an analytical balance in a weighing boat and this is found to be 5.0268 g. The standard deviation in making a single weighing is 0.2 mg. The sodium hydroxide must be accurately standardised (this means its concentration must be accurately determined) by titrating known mass of high-purity potassium hydrogen phthalate, and three such titrations give molar concentrations of 0.1167, 0.1163 and 0.1164 mol L-1. A volume of 36.78 mL of sodium hydroxide is used to titrate each sample. The standard deviation of the burette used is 0.02 mL. Calculate the percentage of acetic acid in the vinegar and its standard deviation.
1. A company illegally dumped their wastewater on a river bank. You are part of an environmental NGO that are tasked to determine what kind toxins that may have contaminated the waters. What kind of analysis would you do? a. Characterization analysis b. Qualitative analysis c. Fundamental analysis d. Quantitative analysis 2. Four groups weighed ten rock samples each, and tested the possibility of outliers using Q-test. At 95.0% confidence (a = 0.05), which of the following is considered to be an outlier? a. 0.024 b. 0.413 c. 0.453 d. 0.674 3. An unknown solution containing oxalic acid, which is a diprotic acid, is titrated against sodium hydroxide. How many mole/s of titrant is needed to react with one mole of analyte? a. ½ b. ¼ c. 2 d. 4
The analysis shows different concentrations based on replicate determinations of Zn in a water sample: 0.754 mg, 0.721 mg, 0.734 mg, 0.731 mg and 0.742 mg. What is the absolute error if the standard solution has 0.750 mg of Zn?
Substance Melting Points in ℃ Benzoic acid 122.3 ℃ Succinimide 125-127 Urea 133 ℃ Cinnamic acid (trans). 133 ℃ Thiourea 182 ℃ Hippuric acid. 187 ℃ For Questions 1-3 assume that you were given 5.00 g of an unknown A for this lab, one of the six compounds whose melting points you looked up for prelab. 1. You recrystallized A and obtained 2.23 g pure product. What was your percent recovery? That is, what percent of the original mass did you get back? Show your work. 2. Assume you took the melting point of the pure product and it was 123oC. Considering…
I need help with calculating the standard deviations and percent error- (experimental-theoretical/theoretical)*100.The theoretical values for the unknowns are water- 1.00g/mL, ethyl alcohol- 0.79g/mL and glycerol - 1.26g/mL. The down arrows mean the number is the same for that column
What is the relative error in the ppt of the following data if the accepted value is 70.05 M? 70.24 M, 70.22 M and 70.10 M
Is the concentration of the solution prepared in the question below only approximate because sodium hydroxide is not a primary standard? * Find the mass in grams of sodium hydroxide that will be required to prepare a solution with a concentration of 0.500 mol·dm⁻³ in a 250 cm³ volumetric flask. [Round the answer to three decimal places. Do not type in the unit. Use a decimal point.] *
An excess of 0.34 mg Pb is obtained from an assay test determined in an analysis. What is the percent relative error in ppt if the mass of the sample is 550 g?
For EACH type of gravimetric analysis:Give actual applications of each analysis. Include the SPECIFIC methodology for each sample chosen.