Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
8th Edition
ISBN: 9781305387102
Author: Kreith, Frank; Manglik, Raj M.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 1, Problem 1.54P
The soldering iron tip in Problem 1.53 becomes oxidized with age and its gray-body emittance increases to 0.8. Assuming that the surroundings are at 20°C, determine the power requirement for the soldering iron.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Derive the expression for radiation heat exchange between two gray surfaces connected by single refractory surface.
You want to have an illuminance of 300 lux on Mrs. Pott (under the SPOTLIGHT#1). What is the Luminous Flux (lumen) the lamp need to releases assuming homogeneous distribution of the light in the illuminated circle?
Could someone use this same problem but tell me how to find the total emissive power of the sheet at the initial state?
Chapter 1 Solutions
Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)
Ch. 1 - 1.1 On a cold winter day, the outer surface of a...Ch. 1 - 1.2 The weight of the insulation in a spacecraft...Ch. 1 - 1.3 A furnace wall is to be constructed of brick...Ch. 1 - 1.4 To measure thermal conductivity, two similar...Ch. 1 - To determine the thermal conductivity of a...Ch. 1 - A square silicon chip 7mm7mm in size and 0.5-mm...Ch. 1 - A cooling system is to be designed for a food...Ch. 1 - 1.80 Describe and compare the modes of heat loss...Ch. 1 - Heat is transferred at a rate of 0.1 kW through...Ch. 1 - 1.10 A heat flux meter at the outer (cold) wall of...
Ch. 1 - 1.11 Calculate the heat loss through a glass...Ch. 1 - 1.12 A wall with a thickness is made of a...Ch. 1 - 1.13 If the outer air temperature in Problem is...Ch. 1 - Using Table 1.4 as a guide, prepare a similar...Ch. 1 - 1.15 A thermocouple (0.8-mm-diameter wire) used to...Ch. 1 - Water at a temperature of 77C is to be evaporated...Ch. 1 - The heat transfer rate from hot air by convection...Ch. 1 - The heat transfer coefficient for a gas flowing...Ch. 1 - 1.19 A cryogenic fluid is stored in a...Ch. 1 - A high-speed computer is located in a...Ch. 1 - 1.21 In an experimental set up in a laboratory, a...Ch. 1 - 1.22 In order to prevent frostbite to skiers on...Ch. 1 - Using the information in Problem 1.22, estimate...Ch. 1 - Two large parallel plates with surface conditions...Ch. 1 - 1.25 A spherical vessel, 0.3 m in diameter, is...Ch. 1 - 1.26 Repeat Problem 1.25 but assume that the...Ch. 1 - Determine the rate of radiant heat emission in...Ch. 1 - 1.28 The sun has a radius of and approximates a...Ch. 1 - 1.29 A spherical interplanetary probe with a 30-cm...Ch. 1 - A spherical communications satellite, 2 m in...Ch. 1 - A long wire 0.7 mm in diameter with an emissivity...Ch. 1 - Wearing layers of clothing in cold weather is...Ch. 1 - A section of a composite wall with the dimensions...Ch. 1 - A section of a composite wall with the dimensions...Ch. 1 - Repeat Problem 1.35 but assume that instead of...Ch. 1 - 1.37 Mild steel nails were driven through a solid...Ch. 1 - Prob. 1.38PCh. 1 - 1.39 On a cold winter day, the outside wall of a...Ch. 1 - As a designer working for a major electric...Ch. 1 - 1.41 A heat exchanger wall consists of a copper...Ch. 1 - 1.43 A simple solar heater consists of a flat...Ch. 1 - A composite refrigerator wall is composed of 5 cm...Ch. 1 - An electronic device that internally generates 600...Ch. 1 - 1.47 A flat roof is modeled as a flat plate...Ch. 1 - A horizontal, 3-mm-thick flat-copper plate, 1-m...Ch. 1 - 1.49 A small oven with a surface area of is...Ch. 1 - A steam pipe 200 mm in diameter passes through a...Ch. 1 - 1.51 The inner wall of a rocket motor combustion...Ch. 1 - 1.52 A flat roof of a house absorbs a solar...Ch. 1 - Determine the power requirement of a soldering...Ch. 1 - 1.54 The soldering iron tip in Problem 1.53...Ch. 1 - Prob. 1.55PCh. 1 - A pipe carrying superheated steam in a basement at...Ch. 1 - Draw the thermal circuit for heat transfer through...Ch. 1 - 1.60 Two electric resistance heaters with a 20 cm...Ch. 1 - 1.63 Liquid oxygen (LOX) for the space shuttle is...Ch. 1 - The interior wall of a large, commercial walk-in...Ch. 1 - 1.67 In beauty salons and in homes, a ubiquitous...Ch. 1 - The heat transfer coefficient between a surface...Ch. 1 - The thermal conductivity of fibreglass insulation...Ch. 1 - 1.71 The thermal conductivity of silver at 212°F...Ch. 1 - 1.72 An ice chest (see sketch) is to constructed...Ch. 1 - Estimate the R-values for a 5-cm-thick fiberglass...Ch. 1 - A manufacturer in the United States wants to sell...Ch. 1 - Referring to Problem 1.74, how many kilograms of...Ch. 1 - 1.76 Explain a fundamental characteristic that...Ch. 1 - 1.77 Explain each in your own words. (a) What is...Ch. 1 - What are the important modes of heat transfer for...Ch. 1 - 1.79 Consider the cooling of (a) a personal...Ch. 1 - Describe and compare the modes of heat loss...Ch. 1 - A person wearing a heavy parka is standing in a...Ch. 1 - Discuss the modes of heat transfer that determine...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A tungsten filament is heated to 2700 K. At what wavelength is the maximum amount of radiation emitted? What fraction of the total energy is in the visible range (0.4to0.75m)? Assume that the filament radiates as a graybody.arrow_forwardThe tungsten filament of an incandescent light bulb has a temperature of approximately 3000 K. The emissivity of tungsten is approximately 1/3, and you may assume that it is independent of wavelength. To increase the efficiency of an incandescent bulb, would you want to raise or lower the temperature? (Some incandescent bulbs do attain slightly higher efficiency by using a different temperature.)arrow_forwardA body at 1100ºc in a black surrounding at 550ºc has emissivity of 0.4 at 1100ºc and emissivity 0.7 at 550ºc. calculate the rate of heat loss by radiation per unit surface area; i) when the body is assumed to be grey with emissivity 0.4 ii) when the body is not grey. (assume absorptivity is independent of the surface temperature)arrow_forward
- Liquefied natural gas (LNG) is transported around the globe using ships similar to thatshown in Figure QA3. This ship has four pressurised cylindrical steel tanks each ofradius of 20 m. The tanks are internally insulated with 30 cm of polyurethane foamwhich keeps the LNG at a constant -162 ºC. Take the effective sky temperature is 265K and the net radiative thermal energy exchange with the sky as 1x106 W. Calculate the surface temperature of the end (facing the sun) of a tank. Calculate the conductive heat transfer through the end (facing the sun)of a tank.arrow_forwardLiquefied natural gas (LNG) is transported around the globe using ships similar to thatshown in Figure QA3. This ship has four pressurised cylindrical steel tanks each ofradius of 20 m. The tanks are internally insulated with 30 cm of polyurethane foamwhich keeps the LNG at a constant -162 ºC. Take the effective sky temperature is 265K and the net radiative thermal energy exchange with the sky as 1x10^6 W. (a) Calculate the surface temperature of the end (facing the sun) of a tank.(b) Calculate the conductive heat transfer through the end (facing the sun)of a tank. answers: a) 375K b) 22.1kWarrow_forwardLiquefied natural gas (LNG) is transported around the globe using ships similar to thatshown in Figure QA3. This ship has four pressurised cylindrical steel tanks each ofradius of 20 m. The tanks are internally insulated with 30 cm of polyurethane foamwhich keeps the LNG at a constant -162 ºC. Take the effective sky temperature is 265K and the net radiative thermal energy exchange with the sky as 1x10^6 W. (a) Calculate the surface temperature of the end (facing the sun) of a tank.(b) Calculate the conductive heat transfer through the end (facing the sun)of a tank. DATA FOR QUESTION: Thermal conductivity, polyurethane foam = 0.02 W/mKStefan’s Constant = 5.67x10^-8 W/m^2K^4Emissivity, steel = 0.95 answers: a) 375K b) 22.1kWarrow_forward
- Define the absorption of radiation incident on an opaque surface of absorptivity α.arrow_forwardCalculate the radiation in watts per square centimeter from a block of copper at 200°C and at 1000°C. The oxidized copper surface radiates at 0.60 the rate of a black body.arrow_forward4. The filament of a 75 W light bulb may be considered as a black body radiating into a black enclosure at 70° C. the filament diameter is 0.10 mm and length is 5 em. considering the radiation, determine the filament temperature .arrow_forward
- A chamber for heat curing large aluminum sheets lacquered black on both sides operates by passing the sheets vertically between two steel plates 150 mm apart. One of the plates is at 300°C, and the other exposed to the atmosphere, is at 25°C. i) What is the temperature of the lacquered sheet? and ii) What is the heat transferred between the wall when equilibrium has been reached? Neglect the convection effects and the emissivity of lacquered sheet is 1.arrow_forwardA 60mm thick plate with a circular hole of 30mm diameter along the thickness is maintained at uniform temperature of 277°C. Find the loss of energy to the surroundings at 20°C, assuming that the two ends of the hole to be as parallel discs and the metallic surfaces and surroundings have black body characteristics.arrow_forwardTwo parallel gray planes have emissivities of 0.8 and 0.7 and are maintained at 800°C and 1500°C. What is the net radiation energy exchange? What would be the reduction in heat transfer if radiation shield of polished aluminums =0.04 is placed between them.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Thermal Radiation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=FDmYCI_xYlA;License: Standard youtube license