(Oceanography) The pressure, P, exerted on an underwater object can be determined by this
formula:
ρ is the density of water, which is
g is the acceleration caused by Earth’s gravity, which is
h is the object’s depth in the water in feet.
a. Determine the units of P by calculating the units resulting from the right side of the formula.
Check that your answer corresponds to the units for pressure listed in Table 1.1.
b. Determine the pressure on a submarine operating at a depth of 2500 feet.
Want to see the full answer?
Check out a sample textbook solutionChapter 1 Solutions
C++ for Engineers and Scientists
- (Practice) Determine the values of the following integer expressions: a.3+46f.202/( 6+3)b.34/6+6g.( 202)/6+3c.23/128/4h.( 202)/( 6+3)d.10( 1+73)i.5020e.202/6+3j.( 10+3)4arrow_forward(Automotive) a. An automobile engine’s performance can be determined by monitoring its rotations per minute (rpm). Determine the conversion factors that can be used to convert rpm to frequency in hertz (Hz), given that 1rotation=1cycle,1minute=60seconds,and1Hz=1cycle/sec. b. Using the conversion factors you determined in Exercise 7a, convert 2000 rpm into hertz.arrow_forward(General math) The volume of oil stored in an underground 200-foot deep cylindrical tank is determined by measuring the distance from the top of the tank to the surface of the oil. Knowing this distance and the radius of the tank, the volume of oil in the tank can be determined by using this formula: volume=radius2(200distance) Using this information, write, compile, and run a C++ program that accepts the radius and distance measurements, calculates the volume of oil in the tank, and displays the two input values and the calculated volume. Verify the results of your program by doing a hand calculation using the following test data: radius=10feetanddistance=12feet.arrow_forward
- (Thermodynamics) The work, W, performed by a single piston in an engine can be determined by this formula: W=Fd F is the force provided by the piston in Newtons. d is the distance the piston moves in meters. a. Determine the units of W by calculating the units resulting from the right side of the formula. Check that your answer corresponds to the units for work listed in Table 1.1. b. Determine the work performed by a piston that provides a force of 1000 N over a distance of 15 centimeters.arrow_forward1. Supposed a ball is thrown straight up in the air with an initial velocity of 50 feet per second and an initial height of 5 feet. How high will the ball be after 3 seconds? Note: The height after t seconds is given by the expression - 16t+vot+ho, where ve is the initial velocity and he is the initial height.arrow_forward(Practice) State whether the following variable names are valid. If they are invalid, state the reason. prod_a c1234 abcd _c3 12345 newamp watts $total new$al a1b2c3d4 9ab6 sum.of average volts1 finvoltarrow_forward
- State whether the following are true or false. If the answer is false, explain why.c) The expression (x > y && a < b) is true if either x > y is true or a < b is true.arrow_forwardFind the value of the given variable show your solutionarrow_forward(Practice) a. To convert inches (in) to feet (ft), the number of inches should be multiplied by which of the following conversion factors? i. 12 in/1 ft ii. 1 ft/12 in b. To convert feet (ft) to meters (m), the number of feet should be multiplied by which of the following conversion factors? i. 1 m/3.28 ft ii. 3.28 ft/1 m c. To convert sq.yd to sq.ft, the number of sq.yd should be multiplied by which of the following conversion factors? i. 1 sq.yd/9 sq.ft ii. 9 sq.ft/1 sq.yd d. To convert meters (m) to kilometers (km), the number of meters should be multiplied by which of the following conversion factors? i. 1000 m/1 km ii. 1 km/1000 m e. To convert sq.in to sq.ft, the number of sq.in should be multiplied by which of the following conversion factors? i. 144 sq.in/1 sq.ft ii. 1 sq.ft/144 sq.in f. To convert minutes (min) to seconds (sec), the number of minutes should be multiplied by which of the following conversion factors? i. 60 sec/1 min ii. 1 min/60 sec g. To convert seconds (sec) to minutes (min), the number of seconds should be multiplied by which of the following conversion factors? i. 60 sec/1 min ii. 1 min/60 secarrow_forward
- (Physics) a. The weight of an object on Earth is a measurement of the downward force onth e object caused by Earth’s gravity. The formula for this force is determined by using Newton’s Second Law: F=MAeFistheobjectsweight.Mistheobjectsmass.AeistheaccelerationcausedbyEarthsgravity( 32.2ft/se c 2 =9.82m/ s 2 ). Given this information, design, write, compile, and run a C++ program to calculate the weight in lbf of a person having a mass of 4 lbm. Verify the result produced by your program with a hand calculation. b. After verifying that your program is working correctly, use it to determine the weight, on Earth, of a person having a mass of 3.2 lbm.arrow_forwardwrite program to calculate volume of cube,cuboid and cylinder using function overcomingarrow_forward(Mechanics) The deflection at any point along the centerline of a cantilevered beam, such as the one used for a balcony (see Figure 5.15), when a load is distributed evenly along the beam is given by this formula: d=wx224EI(x2+6l24lx) d is the deflection at location x (ft). xisthedistancefromthesecuredend( ft).wistheweightplacedattheendofthebeam( lbs/ft).listhebeamlength( ft). Eisthemodulesofelasticity( lbs/f t 2 ).Iisthesecondmomentofinertia( f t 4 ). For the beam shown in Figure 5.15, the second moment of inertia is determined as follows: l=bh312 b is the beam’s base. h is the beam’s height. Using these formulas, write, compile, and run a C++ program that determines and displays a table of the deflection for a cantilevered pine beam at half-foot increments along its length, using the following data: w=200lbs/ftl=3ftE=187.2106lb/ft2b=.2fth=.3ftarrow_forward
- C++ for Engineers and ScientistsComputer ScienceISBN:9781133187844Author:Bronson, Gary J.Publisher:Course Technology Ptr