Concept explainers
A wave pulse is transmitted down a Slinky, but the Slinky itself does not change position. Does a transfer of energy take place in this process? Explain.
Does the transfer of energy take place in the process of wave pulse transmitted through the slinky.
Answer to Problem 1CQ
Yes, the energy would transfer through the slinky as wave propagating through it.
Explanation of Solution
The formation of wave itself is the transfer of energy through the medium upon which wave travel. Here in this case there must be a transfer of energy in the process of wave pulse transmitted through the slinky.
In slinky the wave produced by the compression or expansion. While doing this the spring would store potential energy. And after releasing the stored potential energy converted to the kinetic energy of the motion. This would go on as long as energy consumes or damped. Thus the wave pulses transmitted through the slinky transfer the energy.
Conclusion:
Therefore, the energy would transfer through the slinky as wave propagating through it.
Want to see more full solutions like this?
Chapter 15 Solutions
The Physics of Everyday Phenomena
- A swimmer in the ocean observes one day that the ocean surface waves are periodic and resemble a sine wave. The swimmer estimates that the vertical distance between the crest and the trough of each wave is approximately 0.45 m, and the distance between each crest is approximately 1.8 m. The swimmer counts that 12 waves pass every two minutes. Determine the simple harmonic wave function that would describes these waves.arrow_forwardScouts at a camp shake the rope bridge may have just crossed and observe the wave crests to be 8.00 m apart. If they shake it the bridge twice per second, what is the propagation speed of the waves?arrow_forwardA quartz watch contains a crystal oscillator in the form of a block of quartz that vibrates by contracting and expanding. An electric circuit feeds in energy to maintain the oscillation and also counts the voltage pulses to keep time. Two opposite faces of the block, 7.05 mm apart, are antinodes, moving alternately toward each other and away from each other. The plane halfway between these two faces is a node of the vibration. The speed of sound in quartz is equal to 3.70 103 m/s. Find the frequency of the vibration.arrow_forward
- Medical Application Ultrasound of intensity 1.50102W/m2 is produced by the rectangular head of a medical imaging device measuring 3.00 by 5.00 cm. What is its power output?arrow_forwardYou are working for a plumber who is laying very long sections of copper pipe for a large building project. He spends a lot of time measuring the lengths of the sections with a measuring tape. You suggest a faster way to measure the length. You know that the speed of a one-dimensional compressional wave traveling along a copper pipe is 3.56 km/s. You suggest that a worker give a sharp hammer blow at one end of the pipe. Using an oscilloscope app on your smartphone, you will measure the time interval t between the arrival of the two sound waves due to the blow: one through the 20.0C air and the other through the pipe. (a) To measure the length, you must derive an equation that relates the length L of the pipe numerically to the time interval t. (b) You measure a time interval of t = 127 ms between the arrivals of the pulses and, from this value, determine the length of the pipe. (c) Your smartphone app claims an accuracy of 1.0% in measuring time intervals. So you calculate by how many centimeters your calculation of the length might be in error.arrow_forwardOn a marimba (Fig. P18.75), the wooden bar that sounds a tone when struck vibrates in a transverse standing wave having three ant modes and two nodes. The lowest-frequency note is 87.0 Hz, produced by a bar 40.0 cm long, (a) Find the speed of transverse waves on the bar. (b) A resonant pipe suspended vertically below the center of the bar enhances the loudness of the emitted sound. If the pipe is open at the top end only, what length of the pipe is required to resonate with the bar in part (a)?arrow_forward
- How do sound vibrations of atoms differ from thermal motion?arrow_forwardA sound wave moves down a cylinder as in Figure 16.17. Show that the pressure variation of the wave is described by P=smax2s2, where s = s(x, t) is given by Equation 16.28.arrow_forwardThe speed of a one-dimensional compressional wave traveling along a thin copper rod is 3.56 ktn/s. The rod is given a sharp hammer blow at one end. A listener at the far end of the rod hears the sound twice, transmitted through the metal and through air, with a time interval t between the two pulses, (a) Which sound arrives first? (b) Find the length of the rod as a function of t, (c) Find the length of the rod if t = 127 ms. (d) Imagine that the copper rod is replaced by another material through which the speed of sound is r. What is the length of the rod in terms of t and r? (e) Would the answer to part (d) go to a well-defined limit as the speed of sound in the rod goes to infinity? Explain your answer.arrow_forward
- Consider the following wave function in SI units: P(r,t)=(25.0r)sin(1.36r2030t) Explain how this wave function can apply to a wave radiating from a small source, with r being the radial distance from the center of the source to any point outside the source. Give the most detailed description of the wave that you can. Include answers to such questions as the following and give representative values for any quantities that can be evaluated. (a) Does the wave move more toward the right or the left? (b) As it moves away from the source, what happens to its amplitude? (c) Its speed? (d) Its frequency? (e) Its wavelength? (f) Its power? (g) Its intensity?arrow_forwardTwo identical loudspeakers are placed on a wall 2.00 m apart. A listener stands 3.00 m from the wall directly in front of one of the speakers. A single oscillator is driving the speakers at a frequency of 300 Hz. (a) What is the phase difference in radians between the waves from the speakers when they reach the observer? (b) What If? What is the frequency closest to 300 Hz to which the oscillator may be adjusted such that the observer hears minimal sound?arrow_forwardA train sounds its horn as it approaches an intersection. The horn can just be heard at a level of 50. dB by an observer 10 km away. (a) What is the average power generated by the horn? (b) What intensity level of the horns sound is observed by someone waiting at an intersection 50. m from the train? Treat the horn as a point source and neglect any absorption of sound by the air.arrow_forward
- Glencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-HillPrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax CollegePhysics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning