Sustainable Energy
1st Edition
ISBN: 9781133108689
Author: Richard A. Dunlap
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
error_outline
This textbook solution is under construction.
Students have asked these similar questions
b) Water flows from a large reservoir through a pipe system which consists of 200 mm diameter ofpipe and 50 mm diameter of nozzle as shown in Figure 3. By neglecting all energy losses, calculate;(iii) Total energy at A
A 75 gal. electric hot water heater provides 9000 Watts of power to heat water. If the heater is filled with water at an initial temperature of 50ºF, how long will it take for the water to reach 140ºF? Assume that there are no heat losses.
A stove element draws 15 A when connected to a 240-V line. How long does it take to consume 60 kJ .
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A manufacturing facility consumes 40 m^3/h of water taken from a nearby river located 15 m below the factory tank.Calculate the daily pumping cost if water is conveyed through a 3in, 240 m-long pipe, including friction losses. The cost of electrical energy is 0.831 pesos/kilowatt-hour and the pump operates with 80% efficiency.arrow_forwardA water main is an 18-in-diameter concrete pressure pipe. Calculate the energy loss over a 1-mile length if it carries 7.50 ft/s of water.arrow_forwardAtmospheric air is blowing at 55 km per hour in a windy province. A windturbine generator set with over-all efficiency of 34.8% and a fan blade diameter of 20 meters is to be installed. Calculate the power that can be generated if the average air temperature is 28 degrees C.arrow_forward
- In the figure shown below, it is desired to pump 5408732 lit/day of water from a stream to a pool. El. A = 60m while El. B = 92 m. If the combined pump and motor efficiency is 81%, calculate the monthly power cost in pesos if electricity rate is P12 per kW-hr. Assume that the pump operates for 24 hours and take 1 month = 31 days; Pipe 1: 1613 m, 223 mm, 128 (Length, diameter, Hazen Coefficient) Pipe 2: 1987 m, 287 mm, 123 (Length, diameter, Hazen Coefficient) Pipe 3: 813 m, 206 mm, 134 (Length, diameter, Hazen Coefficient) Round your answer to 4 decimal places.arrow_forwardSuppose the pump of Fig. is situated between two water tanks with their free surfaces open to the atmosphere. Which free surface is at a higher elevation—the one corresponding to the tank supplying water to the pump inlet, or the one corresponding to the tank connected to the pump outlet? Justify your answer through use of the energy equation between the two free surfaces.arrow_forwardFor a building located in Madrid, Spain with annual heating degree-days (dd) of 4654, a heating load (heat loss) of 30,000 kj/h, and a design temperature difference of 30° C (20° C indoor), estimate the annual energy consumption. If the building is heated with a furnace with an efficiency of 92%, how muchgas is burned to keep the home at 20° C? State your assumptions.arrow_forward
- An ESP is to he designed to treat 9000 m3/min of gas to remove particles at 99.8% efficiency. Using Figure 5.10, estimate the required corona power in kW.arrow_forwardWhat is the cost to pump 1000 liters of water to the top of a 30 m high water tank? Assume a pumping efficiency of 50% and an electrical cost of $0.15 per KW-h. P(h2O) = 1000 ?g/m^3 . 1 m^3 = 1000 litersarrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning
Engineering Fundamentals: An Introduction to Engi...
Civil Engineering
ISBN:9781305084766
Author:Saeed Moaveni
Publisher:Cengage Learning