Machine Tool Practices (10th Edition)
10th Edition
ISBN: 9780132912655
Author: Richard R. Kibbe, Roland O. Meyer, Warren T. White, John E. Neely, Jon Stenerson, Kelly Curran
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter H.2, Problem 1ST
Match the correct letter from figure H-38 to the list of drill parts.
Web Body
Margin Lip relief angle
Drill point angle Land
Cutting lip Chisel edge angle
Flute Body clearance
Helix angle Tang
Axis of drill Tapered shank
Shank length Straight shank
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Handwritten solution recommended.
(1) A twist drill bit is used to drill a hole of diameter 2.0 at 4578.1 rpm at a feed rate of 2.5 in/min. Calculate the MRR in in^3/min. Take "pi" = 3.14. Round your answer to the nearest tenth.
Find the commercial tap drill size for 1⁄2”-20 NF bolt.
-How many holes require drilling?
-What is the center to center distance of the 6mm tapped holes?
-What tap drill is used for holes marked Z?
-How many surfaces are machine finished?
-What are the dimensions of the face marked F & C?
-What are the dimensions have symbols A, E &, B
-In what dihedral angle is the drawing made?
-What is the max and min dimensions of D
-What is the tolerance of measurement D?
Chapter H Solutions
Machine Tool Practices (10th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- q1 Identify the nose radius(in mm) from the following single point tool signature 2-3-5-8-12-15-1. 1 5 8 3arrow_forwardIn directional drilling where the wellbore finished dropping inclination is called _____________________ a. inclination reference b. start of drop c. end of drop d. average anglearrow_forward1. What type of milling machine can be used to make the groove in the shaft?2. The diameter of the shaft is d = 25 mm. Find the width and depth of the groove (use the table below).3. Find the diameter of the tool.4. Find the speed of rotation (RPM N) of the tool during roughing and finishing.The material of the shaft is Stainless Steel (C45) with CARBIDE TOOL.arrow_forward
- The part in Figure 1 is to be drilled on a turret-type drill press. The part is 15.0 mm thick. Threedrill sizes will be used: 8 mm, 10 mm, and 12 mm, which are to be specified in the part programby tool turret positions TO1, T02, and T03. All tooling is high speed steel. Cutting speed = 75mm/min and feed = 0.08 mm/rev. Use the lower-left corner of the part as the origin in the x-y axissystem. Write the part program in the word address format using absolute positioning.arrow_forwardWhat would be the lead of a ¾ inch diameter drill with an include angle of 118 degreesarrow_forwardIdentify the type of milling operation in which the cutter axis is perpendicular to the workpiece being machined. straddle milling face milling gang milling angular milling Milling Machine tool is an example of two axes machines Select one: True Falsearrow_forward
- what is the MMC of shaft dimension 1.375 /- .030?arrow_forwardState the uses of each tools: 1. parting off tool 2.boring tool 3. undercutting tool 4. thread tool 5. forming tool 6. shoulder turning tool 7. grooving tool 8. counter boring tool 9. champering tool 10. facing tool 11. threading tool Don't write. Please answer in type writtenarrow_forwardIn drilling operations, the height of the generated hole constrained by: a) Cutting angle b) Shank length c) Body length d) Flute length e) Over all lengtharrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
HOME SHOP JIGS & FIXTURES PART 1, TYPES OF JIGS & ACCESSORIES AND THE THEORIE BEHIND THE TOOLS; Author: THATLAZYMACHINIST;https://www.youtube.com/watch?v=EXYqi42JimI;License: Standard Youtube License