Lab 14 - Polarization of light

.docx

School

Miami Dade College, Miami *

*We aren’t endorsed by this school

Course

2049L

Subject

Electrical Engineering

Date

Dec 6, 2023

Type

docx

Pages

Uploaded by smgomez14

Polarization of light -> Student name: Sharon Gomez I. Objectives: 1. Observe the change in light intensity of light passing through crossed polarizing filters. 2. Measure the transmission of light through two polarizing filters as a function of the angle between their axes and compare it to Malus’s law. II. METHODS AND APPARATUS: Lab #14: Polarization of light - Optical bench - Set of Polarization Procedure: 1. Place the light source, polarizing filters, and Light Sensor so light passes through the filters and then into the sensor. You will rotate only one filter to change the transmission; the other filter, the light source, and the sensor must not move. Turn on the light source. 2. Connect the Light Sensor to Channel 1 of the interface. If your sensor has a range switch, set it to the 600 lux range. 3. Open the file “28 Polarization of Light” in the Physics with Vernier folder. Light intensity is plotted vs. analyzer angle. Data will be collected in Events with Entry mode, meaning that the light intensity will only be measured when the button is clicked. You will then type the analyzer angle in degrees and click to complete the data point. 4. Rotate the analyzer until the Light Sensor reading is maximized. The Light Sensor reading is shown in the status bar at the bottom of the Logger Pro window. If the reading is larger than 600 lux, reduce the intensity of the light source and rotate the analyzer again for maximum sensor reading. This is your zero angle. The axis marks on the two filters should be parallel. 5. Set the filters so their axes are at right angles. Very little light should get through the pair of filters. Define the light level as zero by clicking . The intensity reading should now be near zero. 6. Return the analyzer to the parallel position. Click to begin data collection. Click to take the first point and enter 0 for the angle. Click to complete the entry. 7. Rotate the analyzer by 15º, click , and enter 15 for the angle. Repeat this process, entering 30 for the next angle, and so forth, until you have rotated the analyzer through one revolution, or 360º. Click to end data collection. III. SUMMARY OF THEORY . Perhaps you have seen a display of polarized sunglasses in a store. You can quickly test to see if the glasses are really polarized by looking through the lenses of two glasses and rotating one pair by 90º. If both pair of glasses are polarized, the lenses will appear to go black. Why is that?

To explain the darkened lenses, we need to think of the light as an electromagnetic wave. An electromagnetic wave has varying electric and magnetic fields perpendicular to the direction the wave is traveling. This experiment focuses only on the electric field variation, represented by a vector. Light emitted from a typical source such as a flashlight is randomly polarized, meaning that the electric vector points in varying directions. An ideal polarizing filter will remove all but electric fields that are parallel to the axis of the filter. The light remaining is then said to be polarized. A second filter can be used to detect the polarization; in this case, the second filter is called an analyzer. The transmission through the second filter depends on the angle between its axis and the axis of the first filter. In this experiment you will study the relationship between the light intensity transmitted through two polarizing filters and the angle between the filter axes. P o l a r i z i n g f i l t e r s Preliminary questions 1. Place one polarizing filter on top of a second so you have to look through both of them. Rotate the top filter until the axis marks are at right angles to one another. What do you notice? 2. Rotate a filter so the axes are now parallel. Look through the stack and rotate the top filter about your viewing axis by 180º. Make a qualitative graph of the transmitted light intensity you observed as a function of the angle. IV. ANALYSIS . 1. Describe your graph of light intensity vs. angle, giving important patterns and points. → The graph actually starts at a maximum at 0º, then reduce to a minimum value of 1.9 lux at 90º, which means that the light intensity was at its maximum value (brightness) through the polar filters when the filter’s axes are parallel and was at its minimum value (dimmest) through the polar filters when the filter’s axes are perpendicular. 2. In the 1800’s Malus proposed I = I 0 cos 2 ( θ ) to predict the light transmission through two polarizing filters, where I0 is the intensity when the angle  between the polarizer axes is zero. You can use the Manual Fit feature of Logger Pro to superimpose this relationship on your experimental data. Select Curve Fit from the Analyze menu. Select a Manual Fit Type and click the Define Function button. Enter A*(cos(x))^2. In this equation x stands for the angle  . Click .

3. To compare your data to the model, you must adjust the value of A so that A matches the maximum intensity of your data. To do this, either enter a number in the A field or click to the right of the A parameter field. Adjust A as needed to achieve a good fit to your experimental data. 4. Click to plot your data and the Malus’s law model on the graph at the same time. → Light Intensity and Angle θ(º) Light Intensity (Illumination (lux)) Angle θ (º) 52.2 lux 0º 49.4 lux 15º 42.2 lux 30º 30.6 lux 45º 19.5 lux 60º 9.7 lux 75º 7.8 lux 90º 13.8 lux 105º 25.5 lux 120º 39.5 lux 135º 50.3 lux 150º 57.3 lux 165º 56.8 lux 180º 52.4 lux 195º 40.5 lux 210º 29.3 lux 225º 17.1 lux 240º 8.4 lux 255º 8.2 lux 270º 14.2 lux 285º 24.6 lux 300º 37.0 lux 315º 47.2 lux 330º 55.2 lux 345º 57.3 lux 360º 5. Compare the data to the model. Are your data consistent with Malus’s law? → When the experimental data was compared to the model, it was in agreement with the model. The experimental data proved to be consistent with Malus’s law. Extensions 1. Polarized sunglasses selectively remove glare caused by light reflected by horizontal surfaces, e.g., the hood of a car or a wet highway. For polarized sunglasses to be effective, the glare must be polarized. Devise an experiment to measure how strongly polarized the glare is compared to sunlight or to a flashlight. You will need a smooth horizontal surface to create glare, a bright light source, a polarizing filter, and your Light Sensor and interface. How is the axis of the polarizer oriented when the glare is minimized? → When an unpolarized beam of light passes through a polarizer, then the intensity of the incident light beam reduces to half after passing through it, also it gets polarized.

Your preview ends here

Eager to read complete document? Join bartleby learn and gain access to the full version