20 Ohms Law

In the circuit shown in the figure, draw vx and v0 with a scale according to the input voltages. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, threshold voltages of diodes shall be VE = 0.7V.

Draw vx and v0 according to the input voltages in the circuit shown in the figure. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, the threshold voltages of diodes will be VE = 0.7V.

2. Draw the graph of the voltage across the 10K resistor (calculate the values ​​for the different voltages across the 10K resistor) of the circuit in the figure, knowing that the voltage source V is sinusoidal. And the diodes are silicon

Please solve both questions 3-23 and 3-24 Solve fast it's urgent.

Half-wave rectifier loaded with R-L is fed with a 120 VAA 60 Hz source. 10 Ω loadFind the inductance value that limits the average load current to 5A for the resistance.

Can you draw me a half size breadboard circuit with a 9V source, a multimeter, 220ohm resistor in series and a 1N914 forward biased diode? Im reading about 9.8mA and others are reading 35.02mA. Can you tell me what about it should read for current and voltage? The simulation has two multimeters but we only use one for the live experiment. I feel like Im getting low current reading so I may have it wired wrong.

Question 5 Assume the zener diodes are all ideal in the circuit below and let V1=3.7 V, R1=935 2, R2=1,04702, and R3=855. Determine the output voltage Vo. Express your answer in Volts and round to the 1st digit to the right of the decimal. R1 V1 D1 5V R2 D2 3V {R3 D3 2V Vo

If one of the diodes in the figure below is open, the average voltage across the load is:(a) increases (b) decreases (c) does not change

10 K D3 The diodes in the circuit are Silicon with forward voltage of 0.7 V. Fill up the table showing the state, voltage and current of each of the diodes. Show how you validated the state of each diode. Follow the reference shown in determining whether the diode voltages and currents are positive or negative. D1 8 K 5 V 1K D2 f)1 mA Diode State VD İD + Vp D1 すー D2 D3

i need the answer quickly

what is the letter of the answer?

A Moving to another question will save this response. Question 13 The density of doping of zener diode is less than normal diode. True False A Moving to another question vwill save this response. Windows

When resistors with higher wattage ratings are required, resistors are generally used to dissipate the excessive heat. a) Variable b) Fixed c) Wirewound d) Preset The diode is considered shorted when both anode and cathode has a) Low resistance b) High resistance c) Different resistance d) None of the above When two resistors are connected in parallel then their overall power rating is a) Increased b) Decreased c) Doubled d) Reduced

multirange ammeter was designed using direct method to give three scales with Rsh1= 0.001285989 0, Rsh2=0.000562552 0, and Rsh3=0.000100001 Q. The d'Arsonval meter has Rm=6 Q and full scale current of 1.5 mA. Find the ranges.? 8 (Ctrl) -

Using second approximation for a diode to calculate the load voltage.

For the diode circuit shown below, indicate the ON/OFF condition for all the diodes given VA and VB values. Calculate Vout, Vx and all the currents that flow through the diodes. Summarize your result using a table. +4V VA VB VA OV OV 4V D₁ D₂ X 5ΚΩ D3 VB OV 4V 4V -2V 5ΚΩ VOUT

Note: Please do not handwritten.

4. Develop the schematic for the circuit board in Figure below and determine what type of circuit it is Output 1 ac inputs Gnd Output 2 |D2 Rectifier diodes: 1N4001A Zener diodes: D1-1N4736A, D2-1N4749A

Calculate the current flowing through the given circuit and the voltage value at the V0 ends. (Threshold voltage = 0.3V for Germanium diodes, Threshold voltage for silicon diodes = 0.6V)

Dont use AI or chatgpt I will dislike and report your answer

how to simulate this using multisim?

b. Full-wave Center-tapped Rectifier. Consider the following circuit on the right. D1 2:1 IN4001 +100 V - - b.1 Show the voltage waveforms across each half of the secondary winding and across RL when a 100 V peak sine wave is applied to the primary winding; b.2 What minimum PIV rating must the diodes have? V out Vin OV RL 10 kN -100 V 1N4001 ellee

For the Precision Rectifier in Figure 3, what is the output voltage equation during the Negative-Half Cycle using ideal diodes? choose the correct answer: 1)V0=0V 2)V0=-Vin 3)V subscript o equals negative R subscript 1 over R subscript 2 V subscript i n end subscript 4)V subscript o equals fraction numerator negative R subscript 2 over denominator R subscript 1 end fraction V subscript i n end subscript

Q*: Calculate the current through 48 Q resistor in the circuit shown in Figure(i).Assume the diodes to be of silicon and forward resistance of each diode is 1 Q. D D2 48 2 ww 10 V= D4 D3 (i)

Determine the voltage across the resistor, the current in the resistor, and the output voltage in figure 1 and figure 2. Plot these waveforms with proper ac cycle phase alignment. 1SR154-400 is a silicon rectifier 1 ampere diode. Indicate the peak values as per calculation.

take Vs=333V round off to 3 decimal places

For the following bridge rectifier circuit, assume Vm = 5 V. Plot the waveshape Vo (t) as a function of t for one full period. Assume the diodes are ideal with VD = 0 V. Find Vdc value in V after rectification.     Please sir read the question step by step and answer step by step.

If the line voltage in the figure is increased, ideally +5 V output Please choose one: a. increase b. reduction c. constant

If the PIV rating of the diodes in the figure is increased, the current flowing through the RL Please choose one: a. increase b. constant c. reduction

8. Draw the output waveform for the circuit shown below given Vin(pp)=20V. Write the name of the circuit. D1 and D2 are Germanium Diodes. R2 D1 D2 V82 1.8V 2 10k VIN V81 T2.2V