DAT 223 Project One Proposal Trazel K

1. Outline/Give Two examples for job factors that could lead to poor/bad health and safety behaviour in the workplace? 2. Give thegning limit FB 3. Me 0 4. Before repair work or maintenance of electrical equipment and devices is started, WHAT steps are necessary to undertake to have maximum electrical safety? 5. What power tool is most likely to cause a burn hazard? END Scanned by Candcase

Schedule of Loads and Basic Calculation — Create a tabulated load schedule of your home.

l11 answer 4 5 6

choose the correct answer In solar power plant, the cost of concentrating collector is more than flat platecollector.    TRUE or FALSE

i need the answer quickly

EMF in a circuit is ____. a. Cause current to flow b. Maintains potential difference c. Increases the circuit resistance d. Decreases the circuit resistance e. None of the Choices

In your own words and from your own understanding, avoid plagiarism or copying from the Course Material, explain or describe MOLDED CASE CIRCUIT BREAKER.

I Need the answer as fast as possible please

Solve for all parts. Will give thumbs up

1.a. A fiber optic cable has a minimum bend radius of 8 cm and will be mounted in an expansion loop with support messengers. How far should neighboring support messengers be placed when installing this cable?A. At least 16 cmB. Less than 16 cmC. At least 20 cmD. Exactly 20 cm 1.b. A corner pull box has conduits that are separated by 36 cm. If you install a cable in this pull box, what should the minimum bend radius be?A. At least 8 cmB. Less than 12 cmC. Less than 8 cmD. At least 12 cm

Subject : Electrical Engineering

question 1

Write the answers precisely, do not elaborate unnecessarily, and don't use chatgpt, if i caught it I'm gonna downvote Question: Discuss the electrochemical techniques that are useful to study the capacitive properties of a material. Highlight the importance of each technique

appropriate answer. Statement one The most common causes of death are falls from heights and being struck by vehicles in the workplace Statement two Following HSE guidance should significantly reduce the risk to an individual a) Statement one is correct and statement two is correct b) Statement two is correct and statement one is incorrect c) Both statements are incorrect d) Statement one is correct and statement two is incorrect actclass.co.uk 25 Questi 26 Questi 27 Questi 28 Questi 29 Questi 30 Submit Answers

In a PMMC instrument, operating flux will be produced by the deflection system of the instrument. Select one: True O False

what is error in mesurement system? Also discuss its types

#29 The correct answer is already highlighted, explain in a very simple way why that is the correct answer. Briefly discuss its concept & provide an illustrative example.

The maximum electrical trade size of intermediate conduit is a.) 150 mm b.) 125 mm      c.)  200 mm      d.) 100 mm

17- The electromechanical breakdown depend on the type of the dielectric between two electrodes a- Right. b- Wrong 18- Basic Insulation Level (BIL) is related to the design consideration of the electric device, while Basic protection (BPL) level is related to protection level of the that device. a Right. Wrong. b- 19- As the voltage regulation increased, receiving end voltage will be reduced. Right. b- Wrong 20- We can be using Solar power generation field as a power factor and voltage profile enhancement in Distribution system. (aRight. b- Wrong. 21- From the general electrostatic theories, the field strength at breakdown is given by: a Eb = V/ do =0.6 [Y/ (€ o Er) ] 0.5. b- Eb V/ do = 0.6 [Y / (€ 0/Er )] 0.5. C- Eb V/ do = 0.6 [ Y/(Eo Er) 20.05. d- Eb V/ do = 0.6 [ Y/ (Eo Er) 10.5. 22- Consider plane electrodes with a solid insulator between them. Find the electric field strength at breakdown, if Young's modulus = 10000 (V.F/m2). and the relative permittivity is (36000 TT). If the…

A. Alligned dimensioning system B. Undirectional dimensioning system C. Non of the above

Part 2: Analysis and selection of the Wind Turbine. The team decides at install a 30 MW wind farm. The turbine that has been selected by the local contractor is an Enercon wind turbine. The specifications of all the available Enercon wind turbine is shown in the attached datasheet. 1. Decide on the required number of wind turbines needed. 2. In your own words, explain what the Betz limit for wind turbines means.

If there is an entire row of zero in the Routh table, the system may be marginally stable. TRUE OR FALSE

Note : You have to click SUBMIT before the end of the time. So when the invigilator announce that you F click SUBMIT, then you must click it, otherwise your answers will not be saved. Hi, Mohammed Salim Ahmed Al. When you submit this form, the owner will see your name and email address. Assume that 8oW bulb and 100w bulb are connected in parallel and supplied by 240V ac .When 80w bulb is damaged then .. O Circuit breaker will trip and supply will be cutoff O 100 w bulb also will get damaged after some time O 100w bulb will glow very dim O 100w bulb will continue to glow with same brightness 32°C Sunny A O D 40) G E Chp prt sc delete home 8 backspace { O L 1. pause

Good day, sir/ma'am. Here is the final question which I require assistance with. Thank you very much. Question: A power transmission line is made of copper 1 .80cm in Find the resistance of one mile of this line.

Write short note on the below mentioned questions, Each question carries one mark. Students has to answer the questions typewritten in the word (.docx) format. Figures / Diagrams, equations and solving of problems should be written by hand. Take a picture of it and attach it inside the word file. a) High Voltages are preferred for Transmission of Electricity. Why? b) Why Generation Voltage Levels are low in the range of 11 kV/ 33 kV etc? C) Why ACSR Conductors are preferred over Copper Conductors? d) Overhead Transmission Lines are preferred for Transmission of Power for Long Distances, why? e) Alternating Current is preferred over Direct Current in Power System, Why? f) Write the Installed Generation Capacity of Sultanate of Oman with current energy share of Conventional and Non-Conventional Energy Sources. g) Why the Capacitance effect is neglected in Short Transmission Line. h) Distinguish between Lumped or Distributed elements in a Transmission Line.

FIVE QUESTIONS ANSWER ALL Question 1 A cylindrical specimen of Aluminum having a diameter of 12.8 mm and a gauge length of 50.800 mm is pulled in tension. Use the load-elongation characteristics shown in the following table to complete Q1(a) through (f). Raw Data Load (N) Length (mm) 50.800 7330 50.851 15100 50.902 23100 50.952 30400 51.003 34400 51.054 38400 51.308 41300 51.816 44800 52.832 46200 53.848 47300 54.864 47500 55.880 46100 56.896 44800 57.658 42600 58.420 36400 59.182 a) Plot both the engineering stress versus engineering strain and true stress versus true strain curves on the same axis. EV[8] b) Compute the modulus of elasticity. EV[3] c) Determine the yield strength at a strain offset of 0.002. AN[3] d) Determine the tensile strength of this alloy. AN[2] e) Compute the modulus of resilience. AN[2] f) What is the ductility, in percent elongation? AN[2]