Exam1

A reset input is used in IC 7493, why? a. For reset the counter       b. For setting the counter       c. For decrement of bit by 1       d. For increment of bit by 1

The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False

The signals to the inputs of the FFs and registers are shown below. According to this plot the desired output signals. (NOTE: Solve as rising edge triggered circuit)

%VY l. In. O Homework1.pdf Q: Compute the physical address for the specified operand in each of the following instructions. The register contents and variable are as follows: (CS)=0A00H, (DS)=OB00H, (SS)=OD0OH, (SI)=OFFOH, (DI)=00BOH, (BP)=00EAH and (IP)=0000H, LIST=00FOH, Ax=4020H, BX=250OH. 1) Destination operand of the instruction MOV LIST (BP+DI], AX 2) Source operand of the instruction MOV CL, (BX+200H] 3) Destination operand of the instruction MOV [DI+6400H], DX 4) Source operand of the instruction MOV AL, [BP+SI-400H] 5) Destination operand of the instruction MOV [DI+SP], AX 6) Source operand of the instruction MOV CL, (SP+200H] 7) Destination operand of the instruction MOV (BX+DI+6400H], CX 8) Source operand of the instruction MOV AL, [BP- 0200H] 9) Destination operand of the instruction MOV (SI), AX 10) Destination operand of the instruction MOV (BX][DI]+0400H,AL 11) Source operand of the instruction MOV AX, [ВР+200H] 12) Source operand of the instruction MOV AL, [SI-0100H]…

PLEASE HELP WITH PARTS A,B,C

Name the addressing mode for the following instruction MOV AL, [BX+SI]

You are given the following assembly language statements: MOV AX, 15225 MOV BL, 126 DIV BL SUB BL, AL Just after the CPU finishes executing the SUB instruction, calculate the following: i)The decimal values in AL, AH, and AX registers ii)The decimal value of BL iii)The values of flag bits: Sign, Carry, Auxiliary, Zero, Parity, and Overflow.

Please answer.

con con of son The first 2 pins of the analog pins in Arduino are used to transmit and receive data (TX and RX) O a. False O b. True Which of the following parameters is not a required part in the ARDUINO sketch "for" loop? O a. Initialize O b. Increment OC. Serialprint O d. Condition When an overflow occurred, the C bit in the STATUS register is O a. None of these O b. 0 Oc. Not affected Od 1

12. In which special function register is the bit RS1 located? a) PO b) ACC c) B d) PSW 13. The SiLabs IDE software limits the ROM space to which of the following? a) 2 kB b) 6 kB c) 8 kB d) 64 kB 14. If the accumulator has 00000001B and the command RL A executes, which number remains in the accumulator? a) 01H b) 02H c) 04H d) 08H 15. What is the bit address of the most significant bit in the byte address 20H in the EFM8BB1's internal data memory? a) 00H b) 07H c) 20H d) 27H e) Ro

Solve the following question correctly please.

When an XIC instruction is cleared: a. This enables the next instruction (the rung-condition-out is true). b. This disables the next instruction (the rung-condition-out is false). c. The rung-condition-out is not scanned. d. The rung-condition-out is has to have an OTL.

Must be handwritten No AI based ANSWER

20. An S-R latch does which of the following? A. adds two binary digits, taking the carry value into account B. acts as a memory circuit for a single binary digit C. contains multiple S-R latch circuits D. selects a single output value from a set of input values E. merges multiple input values into a single output value

. (A-)Hand trace the execution of the following program fragments showing what happens to the flags and registers (AL, BL, CL) in each statement supposes that the flags are initially 0. MOV BL, 03H CF SF ZF OF PF AF ADD BL, 02H SUB BL, 05H MOV AL, 00H DEC AL XCHG AL, BL

1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1

please show work included   4. If a 6-bit binary number is used to represent an analog value in the range from -63 to 126, what is the accuracy of the system? In other words, if the binary number is incremented by one, how much change does it represent in the analog value?

Supnorting.cxcentions &interruats Select True/False (T/F) for each statement. Exception usually refers to an event outside of the CPU and interrupt refers to an event inside the CPU. ISelect The CPU checks for exceptions/interrupts after every assembly instruction to get to them tast. Select With polled interrupts, the hardware is responsible to identify the source of the event. Select) With vectored interrupts, the hardware is responsible to identify the source of the event. I Setect)

'Clock The given 4 bit serial in parallel output register is loaded with 1011.If contnpusly clock is applied the after how many clock pulse data become 1011 again?

i need the answer quickly

If Timer 0 is placed in Counter mode as well as in 8 bit Auto reload mode. Timer 1 is placed in Timer mode as well as in 16 bit mode. What is the hex value in TMOD. Use the format as 0x??   Please answer ASAP I will like it please ASAP...

Q4) Design a Register File which includes four 2-bit registers (In total, it includes 8 bits). Each register is named as ala0, b1b0, c2c0, d1d0. Registers are loaded from the S input. In addition to that, there are two input signals, X and Y, to determine which register to select (ie. 00 selectsfirst register ala0 etc). Also there is R signal. When W is zero, the content of the register does not change. When the W is 1 the selected register is loaded with a new value by shifting from the S input. Design this register file by using D flip-flops.

Please answer in typing format

write the name of counter type on the side. this counter what numbers count and whats the mod(....) level(NEED A NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE)

Consider the following assembly program MOV CX, 1100H DLY: SUBS CX, CX, #1 NOP BNE DLY NXT: --- (a) How many times does the BNE DLY instruction get executed? (b) Change the first line of the program so that BNE DLY is executed 34 times (c) Change the second line of the program so that BNE DLY is executed 34 times, while the fist line stays unchanged (MOV CX, 1100H)

Question 2: The HCS12 registers have the values shown in the attached table.Where X, means the values is undefined. Answer the following:A. What is the HCS12 operational mode?B. What is the value on port B pins?C. What is the value on pins PT4-PT7?D. What is the value of X in PTT register?E. Is port B working in full or reduced power?F. What is the pins configuration of CAN2 and CAN4?