report

Design the interfacing circuit shown below and write a program to display single digit (between 0 and 9) prime numbers followed by even numbers, the next odd numbers and repeats in 7-segment displays and its equivalent 8-bit binary value in LEDS. a) When displaying Prime numbers, the first 7-segment display must show "P" and the second 7-segment display must show prime numbers one by one b) When displaying Even numbers, the first 7-segment display must show "E" and the second 7-segment display must show even numbers one by one c) When displaying Odd numbers, the first 7-segment display must show "O" and the second 7-segment display must show even numbers one by one

USE DIGITAL LOGIC AND DESIGN Part 1: In Figure_4; we have 4-bit Comparator using 2-bit Comparators block. You have to satisfy given condition by applying all data on figure 4. At the end, given condition should produce HIGH output and other two should be LOW.   A3 A2 A1 A0 = 1101 and B3 B2 B1 B0 = 1110                                                                            Figure_4   Part 2: The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure_5. Determine the data-output waveforms from D0 through D3.                                                                            Figure_5   Part 3: Decoder can be useful when we have to decode some specific numbers from their equivalent code. Figure 6 has a concept of 3 to 8 line decoder from which you have to generate output waveform from D0 to D7 with proper relationship to input.                                                                      Figure_6   Part 4: The data-input and…

Similar to the GTO, IGBT can be designed to block negative voltage .... What does this sentence mean?What is the advantage block negative voltage??

5. Assume d3d₂d₁do is a BCD number and derive Boolean expression for segments b,c,e,f,g in a seven segment display in terms of d3d₂d₁do g 4 d Based on your boolean expressions derive the values of b,c,e,f,g segments when i. d3d₂d₁do= (0100) 2 ii. d3d₂d₁do = (0111)₂ iii. d3d2d₁do (1000)2

Question iii please help......

The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False

please solve the last 3 parts that is., d,e and f part

Construct the state diagram...

A. Use Microsoft Visual Basic to design a form contain two text boxes and one button called "add", and after click on "add", we get the summation of the numbers between (10 -30), and display the result on text box1 and get the summation of the numbers between (60-80) and display the result on text box2.

Question Vvv For a microprocessor similar to ATmega328p an 8 bit ADC uses a VREF = 3.3 V. When an analog read is executed the return value is 182. What Voltage is present on the input? Enter the value in the box provided in mV. Round to the nearest mV. No units are required .   .Full explain this question and text typing work only     We should answer our question within 2 hours takes more time then we will reduce Rating Dont ignore this line    ..

ii) For the circuit shown in Figure B9, a. Find logic functions for Y and Z. b. Simplify function Z using Boolean algebra. Y Figure B9 AB

A set of five readings is stored in maemory location starting at C060H. Devlop assembly language program (ALP) for 8085 microprocessor to sort the reading in descending order. draw the flow chart for the same.

the diagram on the right is for a register bank circuit that contain 8 registers. Each register is 16-bit. The register can read or write to one register at a time using address bus. Design the circuit and specify the width of EVERY bus.

For a Core2 descriptor that contains a base address of 00333000H, a limit of 0000166AH, and Granularity bit =1. What starting and ending locations are addressed by this descriptor?

Write a Verilog code for 8-bit up/down counter for any type of Modeling.

Logic Gates:* 7404LS (NOT)* 7408LS (AND)* 7432LS (OR)* 7400LS (NAND)* 7402LS (NOR)* 7486LS (EX-OR)Or you can use 74HCxx versions. Task 2: 4 INPUT PRIORITY ENCODERa) Write the truth table.b) Find the outputs in terms of min terms using minimal expression.c) By using K map, find the simple/simplest expression of theoutputs.d) Draw the circuit diagram. (Simulation design will be accepted.)e) Simulate the circuit & explain your results. (Please do notdesign separate simulations for each output. You should design ONEsimulation including all inputs and outputs.)

can someone explain how to do this problem step by step

Binary 4-bit Asynchronous down Counter and explain how it functions, find real life applications

Question 7 election  Assume we have to add two 6-bit numbers in signed integer form. Perform the binary addition and indicate if an overffow occurs. To check, convert both binary operends and your binary sum answer to decimal numbers. . .......    .....................   Full explain this question and text typing work only thanks.

pls solve the 1st 3 parts only. Thnak you

What is not a possible solutions to improve performance ..... of PCM?a. Use of linear PCM codesb. Use of non-linear PCM codes tryc. Use of companded systemsd. Increase number of PCM bits

please help me on this

Need truth table, Verilog code, testbench,circuitry design for 4-bit Fibonacci series generator

The resolution of the ADC unit with the reference voltage value of 3V is set to 8 bits. If the voltage level applied to the ADC input is 1.67 V, what is the numerical value read? For numbers with commas, take 4 digits after commas.?

1. An arithmetic system operates with 3-digit decimal numbers with sign presented in BCD (12 bits), negative numbers utilize the 10's complement form, one decimal digit (4 bits) is occupied by sign: 0 for "+" and 9 for "-". 1a) Show the most positive and the most negative numbers in both decimal and BCD forms. 1b) Present numbers A=+36 and B= -42 in BCD. 1c) Present the 10's complements of A and B in BCD. 1d) Perform the following operations bit-by-bit, show carries, apply BCD correction (add 6) when necessary (the sum of two decimal digits is greater than 9). 1d1) A+B in BCD. 1d2) A - B = A+(-B) in BCD by addition of A and the 10's complement of B. 1d3) B-A= B + (-A) in BCD by addition of B and the 10's complement of A.

A parity bit is "1" on a system which uses odd parity. The data is "C8". The data is: A. Good B. Corrupted C. Artificial D. Real

USE DIGITAL LOGIC AND DESIGN