HW 2

In charpy test specimen, the angle of v-notch section is_- a. 60 degrees o b. 30 degrees O c. 90 degrees o d. 45 degrees

No need of explanation only provide correct answer. So please provide both the answers

All three parts please

Which one of these may increase the amount of contact resistance? Lower temperature during matching of materials decreasing pressure for pressing the materials together Higher surface roughness All of the above Using air as a fluid for the gap instead of liquids

Question 2: Please write a precise overview/description of the precision tweezer below specifically for each part, and not in general.

12)Among the following, which technique can be used for 3D deformation measurement purpose? O Ruller Stereoscopic video imaging system O Dial gauge Straight edge set

total deformation in ansys

1. What is the Position Tolerance for the 2.012/2.008 Diameter Hole? 2. What is the Position Tolerance for the 2.006/2.002 Diameter Stud?

What material is being specified by this section line pattern? (Refer to Figure 6-2.)

. one or more can be correct please select from below options  Lower operating temperatures are more desirable as they reduce the viscosity making it easier to fill the cavity      This process can be used for both thermosets and thermoplastics as they can both be thermally shaped        This process can only be used for thermosets as they can thermally cure from the monomer state         This process is suitable for rubber, PVC and polymethyl methacrylate

1. What best describes this print? * A. Casting B. Forging C. Welding D. Machining 2.  There are GD&T Feature Control Frames on the Print. Check the types that apply. * Flatness Parallelism True Position 3. What company specification number is given to the material for this part?

How many auxiliary views are found on this print?

I need problems 10, 11, and 12 answered pertaining to the print attached below.

TRUE OR FALSE.  ANSWER ALL QUESTIONS OTHERWISE DONT ATTEMPT IT STRICTLY. I WILL REPORT YOU IF U ATTEMPT WITHOUT ANSWERING ALL QUESTIONS.

c) Evaluate the performance of Static Cone Penetration Tests

What is compression testing?

I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave it for another tutor to answer. Thank you.   What tolerance is specified for the depth of the groove featured in the enlarged detail? (Multiple Choice)a. .002'b. .004'c. .005'd. .010' What was the main focus of the last revision of this print? (Multiple Choice)a. Paint coatingsb. Heat treatc. Assembly adhesivesd. Geometric tolerancing

Full film lubricating is a type of lubrication in which the coefficient of friction is low. Select one: True False

what would be the order of operations to make this part in the least amount of time and how would you hold the part?

What is the aerodynamic (equivalent) diameter of an airborne spherical aluminium particle with the diameter of 3 micrometers Group of answer choices 5.31 micrometers 4.36 micrometers 4.61 micrometers 4.93 micrometers (show working)

Which would be the most likely to measure for an inflated baloon? A. Shear modulus b  bulk modulus c young mod   If we want to make sure a piece of metal does not easily get bent out of shape, which would be most important to measure for the metal? A. Young b shear c bulk (modulus)

Need questions 4, 5, 6 explained and answered please!

Q1/B) Match between Column A & B. A B A Good toughness Cutting Fluids HSS B vacuum Serrated or segmented chips Vertical shaper C Horizontal milling machining D vibration E Ductile material machined at low cutting speed Milling Chip load F Interrupted cutting operation G Emulsified Oils continuous Chip with BUE Slitting HCyclical formation of alternating high shear strain followed by low shear strain 1 Slotter Electron beam machining 10 Ultrasonic machining J Feed per cutter tooth 2 Ō88 L9GAGN 3 9 Answer from A

i want full answer with the all steps

Which among the following is a forming process in which thickness of the metal plate is decreased by increasing its length. O a. Rolling O b. Forging O c. Drawing O d. Bending Which of the following metal forming processes is best suitable for making the cup shaped products? ENG 08:37 a US 19/04/20 ho inse

What are three important properties of the media to be used in heavy medium separation

Need help

How is it possible to decrease contact resistance? O By using different fluids for better matching O Using softer metal foils Increasing surface roughness O None of the above O Using higher pressure when combining