1. A standard TTL gate performs what logic function for positive logic? 2. If all inputs of a TTL gate are binary 1, the output will be 3. The typical TTL logic levels are: Binary 0= 4. MOS combining both P- and N-channel in series is called 5. The CMOS logic levels are: binary 0 =_______ volts and binary 1 = volts and binary 1 = - volts. volts.

1. A standard TTL gate performs what logic function for positive logic? 2. If all inputs of a TTL gate are binary 1, the output will be 3. The typical TTL logic levels are: Binary 0= 4. MOS combining both P- and N-channel in series is called 5. The CMOS logic levels are: binary 0 =_______ volts and binary 1 = volts and binary 1 = - volts. volts.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Perform the functions given below with the decoder given below and a suitable logic gate. ?1(?,?, ?) = ∑m( 3, 5, 6) ?2(?,?, ?) =∑m ( 1, 4)
Perform the functions given below with the decoder given below and a suitable logic gate. F1(A,B, C) = ∑m( 3, 5, 6) F2(A,B, C) =∑m ( 1, 4)
Implement Four-to-one-line multiplexer with Logic diagram and Function table.
Design 3 systems that represent minterm 30 for a 5-input system: 1.-using logic gates, with a maximum of two inputs each, which represent a low active output. Ensures efficient interpretation of the diagram 2.- exclusively using two-input NAND logic gates 3.- Using components at TTL level.
What is the vhdl code for 4 bit parallel in parallel out register using d flip flop using logic gates(and ,or,...)?
Design a serial adder using the following: Explain the operation briefly, list thestate table (must include present state, inputs, next state, output and flip-flopinputs) and draw the logic diagrama. Using D flip flop, shift registers and necessary logic gatesb. Using JK flip flop, shift registers and necessary logic gates
Define a 2-bit demultiplexer to be a circuit whose single input line is steered to one of the four output linesdepending on the state of the two control lines (A, B). Draw its logic diagram (to the gate level) and specify the exactstate of A and B for each output line when that output line is selected.
F A,B,C,D) = ∑ (1, 2, 3, 8, 9, 10, 11,14)× d (7, 15) Use Karnaugh map and Quinn McKlausky Method. Draw the logic circuit for the simplified function using NOR gates for both methods. Compare Both methods in terms of cost assuming a Nor gate costs 10 cents.
Draw the logic diagram of a 2-to-4-line decoder using (a) NOR gates only and (b) NAND gates only. Include an enable input.
. Design a combinational circuit to convert a 4-bit binary number to gray code using(a) standard logic gates,(b) decoder,(c) 8-to-1 multiplexer,(d) 4-to-1 multiplexer.
Q5. (a) Convert the following logic gate circuit into a Boolean expression, writing Boolean sub-expressions next to each gate output in the diagram: (b) Realise Ex-NOR gate using universal gate?
Consider a family of logic gates that operate under the static discipline with the following voltage thresholds: VI=1.5V, VOL=0.5V, VIH=3.5V, and VOH=4.4V. a. What is the lowest voltage that can be output by an inverter for a logical 1 output? b. What is the highest voltage that must be interpreted by a receiver as logical 0? c. What is the lowest voltage that must be interpreted by a receiver as logical 1?