1. What will happen to the structure of a soap micelle if it is placed in a non-polar solvent? 2. What will be the maximum weight of a soap produced by saponifying 0.065 moles of a hypothetical fat depicted below? Draw the structure of the main product (soap). I. CH2-O-C(CH2)14CH3 CH-O-C(CH2)14CH3 + 3 NaOH CH2-O-C(CH2)14CH3 3. Sodium methylsulfonate (CH3OSO Na+) is a poor detergent. Explain why.

1. What will happen to the structure of a soap micelle if it is placed in a non-polar solvent? 2. What will be the maximum weight of a soap produced by saponifying 0.065 moles of a hypothetical fat depicted below? Draw the structure of the main product (soap). I. CH2-O-C(CH2)14CH3 CH-O-C(CH2)14CH3 + 3 NaOH CH2-O-C(CH2)14CH3 3. Sodium methylsulfonate (CH3OSO Na+) is a poor detergent. Explain why.

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter89: Thin-layer Chromatography

Section: Chapter Questions

Problem 8P

See similar textbooks

Similar questions

Can someone please help me out with this? It has to have Hyaluronic Acid, (C14H21NO11)n, as either the product or the starting material. Thanks in advance!
) Which of the following compounds will be most soluble in ethanol (CH3CH2OH)? A) ethylene glycol (HOCH2CH2OH) B) hexane (CH3CH2CH2CH2CH2CH3) C) acetone (CH3COCH3)D) trimethylamine (N(CH3)3) E) A and D are soluble in ethanol.
Can you elaborate on how you determined how CH3CH2OH (part B) has a higher delta Hvap? Is this in relation to the london dispersion forces or the lewis diagram?
Rank the following groups in order of decreasing priority. −COOH, −CH2OH, −H, −CHO
Linoleic acid is shown below. What makes this fatty acid particularly susceptible to autoxidation? 1. The red CH bond has a low bond dissociation energy because it is doubly allylic. 2. The red CH bond has a high bond dissociation energy because it is doubly allylic. 3. The red CH bond is the most accessible to reaction with O2 because it is the least sterically crowded CH bond. 4. Both 2 and 3.
p-toluic acid is prepared from 3.42 grams of p-Bromotoluene. When p-Bromotoluene was mixed with dry ether, the mixture was warmed until the ether begins to boil (34.6 °C). When the reaction is almost complete, dry ice (3-4 mL in a beaker) was prepared and the mixture was poured into it. After some time, 5 mL of 6 N HCl was added. The solvent used for the recrystallization is 100 mL of 30% ethanol. The reaction equation is given on the figure. What is the actual yield? What is the theoretical yield? How many moles of p-toluic acid was produced?
Which of these compounds is most soluble in water at pH 7.0? (Note that the non-ionized forms are shown, and remember that ionization will impact solubility!) a) CH3-CH2-HCO-O-CH3 (an ester) b) CH3-CH2-CH2-CH2-NH2 c) CH3-CH2-CH2-CH2-CH2OH d) CH3-CH2-CH2-CH2-CH3 e) CH3-CH2-CH2-CH2-CHO
Rank the following groups in order of decreasing priority. −NH2, −CH2NH2, −CH3, −CH2NHCH3
Good hand written explanation Asap Thanks What is an azeotrope? a) A mixture of compounds that is dangerous to distill. b) Any mixture that cannot be practically separated by distillation c) A set ratio of compounds that can only be distilled in the best equipment under the best conditions. d) A set ratio of two compounds (e.g. 5% ethanol in water) that always distills together at the same time.
Watch the Iodination of Acetone before answering the questions: https://youtu.be/KkpeiuelvTI - If starch was added into the mixture, what will happen to it? What is the purpose of the starch if it was added?
Rank the following groups in order of decreasing priority. −C≡CH, −CH(CH3)2, −CH2CH3, −CH=CH2
Which of these compounds is most soluble in water at pH 7.0? (Note that the non-ionized forms are shown, and remember that ionization will impact solubility!) a CH3-CH2-HCO-O-CH3 (an ester) b CH3-CH2-CH2-CH2-CHO c CH3-CH2-CH2-CH2-CH3 d CH3-CH2-CH2-CH2-NH2