16. Each of the two vertical links CF connecting the two horizontal members AD and EG has a uniform rectangular cross section 4 in. thick and 1 in. wide, and is made of steel with an ultimate strength in tension of 60 ksi. The pins at C and F each have a ½ in. diameter and are made of a steel with an ultimate strength in shear of 25 ksi. Determine the overall factor of safety for the links CF and the pins connecting them to the horizontal members. * 10 in. 16 in. 10 in. D 2 kips

16. Each of the two vertical links CF connecting the two horizontal members AD and EG has a uniform rectangular cross section 4 in. thick and 1 in. wide, and is made of steel with an ultimate strength in tension of 60 ksi. The pins at C and F each have a ½ in. diameter and are made of a steel with an ultimate strength in shear of 25 ksi. Determine the overall factor of safety for the links CF and the pins connecting them to the horizontal members. * 10 in. 16 in. 10 in. D 2 kips

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 350 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. The largest load P that can be applied at A is kN.
In the steel structure shown, a 6-mm-diameter pin is used at C and10-mm-diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Knowing that a factor of safety of 3.0 is desired,determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes.
In the structure shown, an 8-mm-diameter pin is used at A and 12 mmdiameter pins are used at B and D. Knowing that the ultimate shearingstress is 100 MPa at all connections and the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 3.0 is desired.
In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 2.6 is desired.
In the structure shown, an 8-mm diameter pin is used at A, and 12- mm diameter pins are used at B and D. Knowing that the ultimate shearing stresses is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 3.0 is desired.
The eyelet (figure) is used to support a load of 3000 kgf. Determine its diameter d, and the required thickness h, so that the washer does not penetrate or shear the support. Knowing that the eyelet and washer must be made of 1020 steel, cold rolled, with a safety factor of 2.5, and the gap between the screw and the through hole must be 4mm, the steel used will be annealed and threadmachined, and the outer diameter of the washer will be 40mm.
Member ABC, which is supported by a pin and bracket at C and a cable BD, was designed to support the 20-kN load P as shown. The pin at C has 20 mm diameter. a) Draw complete free body diagram of member ABC and determine all forces acting upon it b) If pin at C was made from steel with ultimate shear stress 300 MPa, calculate its factor of safety c) Knowing that rope BD made of a material has allowable stress of 50 MPa, calculate its diameter d) Use the information in part c, find the Young’s modulus of the rope material knowing that its length is 0.5 m and stretched by 0.5 mm upon the shown loading.
Two wooden planks, each 7/8 in thick and 6in wide, are joined by the glued mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 120psi, determine the smallest allowable length d of the cuts if the joint is to withstand an axial load of magnitude P=1200-lb. Note: Seven surfaces carry the load, P=1200-lb
A 20 mm diameter rod BC has flat ends of 20 mm x 40 mm rectangular cross section, while the boom AB has a 30 x 50 mm rectangular cross section and is fitted with a clevis at the end B. Both members are connected at B by a pin from which the 30 kN load is suspended by means of a U-Shaped bracket. Boom AB is supported at A by a pin fitted into a double bracket, while rod BC is connected at C to a single bracket. All pins are 25 mm diameter. Determine the normal stresses in members AB and BC; shearing stresses and bearing stresses at A, B and C.
A load P is applied to a steel plate in which a 12 mm diameter perforated plate is carried. Determine the approximate value (kN) of the largest Pin that can be applied to the tool so that the shear stress in the steel bar does not exceed 100 MPa.
The ABC element is supported by a pin at C and a BD cable. Knowing that the limit load for the BD cable is 150 kN, and the coefficient Safety with respect to cable failure for BD of 3.5 determine the maximum value of the load P that can be supported. Determine the diameter of pin C, knowing that it is made of steel with an admissible stress of σadm = 270 Mpa, and that it is subjected to shear double.
Two links BF are made of steel with a 450-MPa ultimate normal stress and has a 6x12–mm uniform rectangular cross section. Links BF are connected to members ABD and CDEF by 8-mm diameter pins; ABD and CDEF are connected together by a 10-mm diameter pin; CDEF is connected to the support by a 10-mm diameter pin; all of the pins are made of steel with a 170 MPa ultimate shearing stress. Knowing that a factor of safety of 3 is desired, determine the largest load P that may be applied