250 mm 400 mm members AD and EG has a 10 x 40-mm uniform rectangular cross section and is made of a steel with an ultimate strength in tension of 400 MPa, while each of the pins at C and F has a 20-mm diameter and are made of a steel with an ultimate strength in shear of 150 MPa. Determine the overall factor of safety for the links CF and the pins connecting them to the horizontal members. 250 mm 1.53 Each of the two vertical links CF connecting the two horizontal A D E F 24 kN

250 mm 400 mm members AD and EG has a 10 x 40-mm uniform rectangular cross section and is made of a steel with an ultimate strength in tension of 400 MPa, while each of the pins at C and F has a 20-mm diameter and are made of a steel with an ultimate strength in shear of 150 MPa. Determine the overall factor of safety for the links CF and the pins connecting them to the horizontal members. 250 mm 1.53 Each of the two vertical links CF connecting the two horizontal A D E F 24 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

THe bracket shown is made of cold drawn steel with Sy=400MPa and Su=480 MPa, and is fastened to a beam made of the same material by five rivets that are made of a steel with Sy=300 MPa and Sut=365 MPa. The thickness of the bracket and the beam are 12 mm and 16 mm respectively.Diameters of the rivets are 20 mm. What safe load F(steady) can be supported by the riveted joint for a factor of safety of 2. Use distortion energy theory of failure.
1. The structure is used to support a distributed load of w = 15 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3,080 mm^2. The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C.
The five-bolt connection shown must support an applied load of P = 214 kN. If the average shear stress in the bolts must be limited to 249 MPa, determine the minimum bolt diameter that may be used in the connection.
The lap joint is fastened by 20 mm rivets placed alongside each other as shown along the length of the plate. Determine the safety of the lap joint to carry an axial load P=180 KN if the shearing stress in the rivets is limited to 60 MPa, the bearing stress in the plates to 110 MPa, and the average tensile stress in the plate is limited to 140 MPa. Plate width, W=140 mm, splice plate thickness, t=15 mm and main plate thickness, t = 40 mm. P = 180 KN
From the given bracket shown, which consist of two plates riveted to the column by 4-22mm Ø rivets which is subjected to an eccentric load of 150 kN. 1. Which of the following gives the shearing stress due to axial load only? a. 49.325 MPa b. 70.25 MPa c. 80.47 MPa d. 68.25 MPa 2.. Which of the following gives the shearing stress due to moment alone? a. 69.76 MPa b. 70.94 MPa c. 56.39 MPa d. 64.32 MPa 3. Which of the following gives the maximum shearing stress? a. 110.30 MPa b. 120.40 MPa c. 140.50 MPa d. 105.70 MPa
Two fork end pieces are to be joined together by a single steel pin of 25mm diameter and they are required to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of either fork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?
Determine the length of the shortest 2-mm diameter bronze wire, which can be twisted through two complete turns without exceeding a stress of 70 MPa. Use G = 35 GPa.
Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution
The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d1 = 0.625 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]
Two links BF are made of steel with a 450-MPa ultimate normal stress and has a 6x12–mm uniform rectangular cross section. Links BF are connected to members ABD and CDEF by 8-mm diameter pins; ABD and CDEF are connected together by a 10-mm diameter pin; CDEF is connected to the support by a 10-mm diameter pin; all of the pins are made of steel with a 170 MPa ultimate shearing stress. Knowing that a factor of safety of 3 is desired, determine the largest load P that may be applied
A 20 mm square key with a length of 150 mm was used in a 100 mm shaft to fasten a 250 mm spur gear. Determine the force that will cause the key to shear if the shearing stress is 25 MPa. A.60 kN B. 65 kN C. 70 kN D. 75 kN