Example: A 3-phase overhead transmission line has a total series impedance per phase of 200 280° ohms and a total shunt admittance of 0-0013290° Siemen per phase. The line delivers a load of 80 MW at 0-8 p.f. lagging and 220 kV between the lines. Determine the sending end line voltage and current by Rigorous method.

Example: A 3-phase overhead transmission line has a total series impedance per phase of 200 280° ohms and a total shunt admittance of 0-0013290° Siemen per phase. The line delivers a load of 80 MW at 0-8 p.f. lagging and 220 kV between the lines. Determine the sending end line voltage and current by Rigorous method.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.41P

See similar textbooks

Similar questions

Consider a long radial line terminated in its characteristic impedance Zc. Determine the following: (a) V1/I1, known as the driving point impedance. (b) | V2 |/V1|, known as the voltage gain, in terms of al. (c) | I2 |/| I1 |, known as the current gain, in terms of al. (d) The complex power gain, S21/S12, in terms of al. (e) The real power efficiency, (P21/P12)=, terms of al. Note: 1 refers to sending end and 2 refers to receiving end. (S21) is the complex power received at 2; S12 is sent from 1.
A small manufacturing plant is located 2 km down a transmission line, which has a series reactance of 0.5/km. The line resistance is negligible. The line voltage at the plant is 4800V(rms). and the plant consumes 120kW at 0.85 power factor lagging. Determine the voltage and power factor at the sending end of the transmission line by using (a) a complex power approach and (b) a circuit analysis approach.
A 30-km, 34.5-kV, 60-Hz, three-phase line has a positive-sequence series impedance z=0.19+j0.34/km. The load at the receiving end absorbs 10 MVA at 33 kV. Assuming a short line, calculate: (a) the ABCD parameters, (b) the sending-end voltage for a load power factor of 0.9 lagging, and (c) the sending-end voltage for a load power factor of 0.9 leading.
The 500-kV, 60-Hz, three-phase line in Problems 4.20 and 4.41 has a 180-km length and delivers 1600 M W at 475 kv and at 0.95 power factor leading to the receiving end at full load. Using the nominal circuit, calculate the (a) ABCD parameters, (b) sending-end voltage and current, (c) sending-end power and power factor, (d) full-load line losses and efficiency, and (e) percent voltage regulation. Assume a 50C. conductor temperature to determine the resistance of this line.
A single-phase overhead transmission line consists of two solid aluminum conductors having a radius of 3 cm with a spacing 3.5 m between centers. (a) Determine the total line inductance in mH/m. (b) Given the operating frequency to be 60 Hz, find the total inductive reactance of the line in /km and in/mi. (c) If the spacing is doubled to 7 m, how does the reactance change?
A 200-km, 230-kV, 60-Hz, three-phase line has a positive-sequence series impedance z=0.08+j0.48/km and a positive-sequence shunt admittance y=j3.33106S/km. At full load, the line delivers 250 MW at 0.99 p.f. lagging and at 220 k V. Using the nominal circuit, calculate: (a) the ABCD parameters, (b) the sending-end voltage and current, and (c) the percent voltage regulation.
Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the three-phase line in Problem 4.18. Also calculate the line-charging current in kA/phase if the line is 110 km in length and is operated at 230 kV. Neglect the effect of the earth plane.
A 3-phase line having an impedance of (5 + £20) ohm per phase delivers a load of 30 MW at a p.f.,of 0.8 lag and voltage 33 kV. Determine the capacity of the phase modifier required to be installed at the receiving end if the voltage at the sending end is to be maintained at 33 kV.
For a given short transmission line of impedance R+jX ohms/phase, the sendingend and receiving end voltages Vs and Vr are fixed. Derive the expression for themaximum power that can be transmitted over the line.
A three phase 220KV, 50Hz transmission line supplies a power of 100MW at a power factor of 0.8 lag at the receiving end. The Series resistance, reactance, and shunt susceptance per phase per Km are 0.082, 0.8 2, and 6 x 10-6mho respectively. Determine the efficiency and regulation for transmission line lengths of 60Km and 200Km (use π)
In the medium-length power transmission line model given below, since the end-of-line voltage value of the nominal-T equivalent circuit is 154 kv, find the voltage regulation value for this line and draw the phasor diagram.
A 3-phase overhead transmission line has a total series impedance per phase of 200 ∠80º ohms and a total shunt admittance of 0·0013∠90º siemen per phase. The line delivers a load of 80 MW at 0·8 p.f. lagging and 220 kV between the lines. Determine the sending end line voltage and current by rigorous method.