2- i. Answer the questions considering Turkish electricity system. Single phase voltage in residential customers: Three phase voltage in industrial facilities: Transmission line voltage levels: Frequency: Total installed capacity of Turkey in March 2021: Total length of transmission line of Turkey in 2020: volt volt kV, kV, kV, kV Hz MW km ii. What can be the disadvantages if we see 15 volts on the neutral wire? ili. What happens if we have no ground wire in our houses? Iv. What is the difference between installed power and demand power?

2- i. Answer the questions considering Turkish electricity system. Single phase voltage in residential customers: Three phase voltage in industrial facilities: Transmission line voltage levels: Frequency: Total installed capacity of Turkey in March 2021: Total length of transmission line of Turkey in 2020: volt volt kV, kV, kV, kV Hz MW km ii. What can be the disadvantages if we see 15 volts on the neutral wire? ili. What happens if we have no ground wire in our houses? Iv. What is the difference between installed power and demand power?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.48P

See similar textbooks

Similar questions

The following parameters are based on a preliminary line design: per unitVS=1.0, VR=0.9 per unit, =5000km,Zc=320,=36.8. A three-phase power of 700 MW is to be transmitted to a substation located 315 km from the source of power. (a) Determine a nominal voltage level for the three-phase transmission line, based on the practical line-loadability equation. (b) For the voltage level obtained in part (a), determine the theoretical maximum power that can be transferred by the line.
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
The 500-kV, 60-Hz, three-phase line in Problems 4.20 and 4.41 has a 180-km length and delivers 1600 M W at 475 kv and at 0.95 power factor leading to the receiving end at full load. Using the nominal circuit, calculate the (a) ABCD parameters, (b) sending-end voltage and current, (c) sending-end power and power factor, (d) full-load line losses and efficiency, and (e) percent voltage regulation. Assume a 50C. conductor temperature to determine the resistance of this line.
With the same transformer banks as in Problem 3.47, Figure 3.41 shows the oneline diagram of a generator, a step-up transformer bank, a transmission line, a stepown transformer bank, and an impedan load. The generator terminal voltage is 15 kV (line-to-line). (a) Draw the per-phase equivalent circuit, aounting for phase shifts for positive-sequence operation. (b) By choosing the line-to-neutral generator terminal voltage as the reference, determine the magnitudes of the generator current, transmiss ion-line current, load current, and line-to-line load voltage. Also, find the three-phase complex power delivered to the load.
Consider the single-Line diagram of a power system shown in Figure 3.42 with equipment ratings given: Generator G1: 50MVA,13.2kV,x=0.15p.u. Generator G2: 20MVA,13.8kV,x=0.15p.u. Three-phase -Y transformer T1: 80MVA,13.2/165YkV,X=0.1p.u. Three-phase Y- transformer T2: 40MVA,165Y/13.8kV,X=0.1p.u. Load: 40MVA,0.8PFlagging,operatingat150kV Choose a base of 100 MVA for the system and 132-kV base in the transmission-line circuit. Let the load be modeled as a parallel combination of resistance and inductance. Neglect transformer phase shifts. Draw a per-phase equivalent circuit of the system showing all impedances in per unit.
Transmission line conductance is usually neglected in power system studies. True False
Figure 3.39 shows a oneline diagram of a system in which the three-phase generator is rated 300 MVA, 20 kV with a subtransient reactance of 0.2 per unit and with its neutral grounded through a 0.4- reactor. The transmission line is 64km long with a cries reactance of 0.5-/km. The three-phase transformer T1 is rated 350MVA.230/20kV with a leakage reactance of 0.1 per unit. Transformer T2 is composed of three single-phase transformers, each rated 100 MVA, 127/13.2kV with a leakage reactance of 0.1 per unit. Two 13.2kV motors M1 and M2 with a subtransient reactance of 0.2 per unit for each motor represent the load. M1 has a rated input of 200 MVA with its neutral grounded through a 0.4- current-limiting reactor, M2 has a rated input of 100 MVA with its neutral not connected to ground. Neglect phase shifts associated with the transformers. Choose the generator rating as base in the generator circuit and draw the positive-sequence reactance diagram showing all reactances in per unit.
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
Three ACSR Drake conductors are used for a three-phase overhead transmission line operating at 60 Hz. The conductor configuration is in the form of an isosceles triangle with sides of 20, 20, and 38 ft. (a) Find the capacitance-to-neutral and capacitive reactance-to-neutral for each 1-mile length of line. (b) For a line length of 175 mi and a normal operating voltage of 220 kV, determine the capacitive reactance-to-neutral for the entire line length as well as the charging current per mile and total three-phase reactive power supplied by the line capacitance.
A single circuit 60 Hz transmission line. the conductors are Linnet type with flat horizontal spacing of 17.46 feet between conductors. Determine: (a) Assume that the line is short with a length of 50 miles, calculate the parameters of the line and draw the equivalent circuit. (b) Assume that the line is average with length of 150 miles (Pi-nominal model). draw the pi-nominal circuit for the transmission line and calculate its parameters (Z and Y/2 values, where Z is the series impedance of the transmission line and Y is the shunt admittance).
The impedance seen from the relay side in a distance relay is 10 ohms. Given that the CT ratio is 1000 : 1 and the PT ratio is 100,000 : 110, determine the actual impedance. Given that the line has a resistance of 1 milliohm per km and a reactance of 20 milliohm per km, find the distance to fault. Assume single-phaseline.
Define power system. Write down the characteristics of transmission line.