#2 The joint is fastened together using two bolts. Determine the required diameter of the bolts if the shear stress failure for the bolts is Tau = 350MPA. Use a Factor of Safety for Shear of F.S. = 2.5. Set up your FBD and forces on bolts correctly i Tip: F.S. = 80 kN 30 mm- 30 mm 40 kN 40 kN

#2 The joint is fastened together using two bolts. Determine the required diameter of the bolts if the shear stress failure for the bolts is Tau = 350MPA. Use a Factor of Safety for Shear of F.S. = 2.5. Set up your FBD and forces on bolts correctly i Tip: F.S. = 80 kN 30 mm- 30 mm 40 kN 40 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.3P: A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is...

See similar textbooks

Related questions

Q: 1.36 The bell crank, which is in equilibrium under the forces shown in the figure, is supported by a…

A: As per given We have to determine the required diameter of rod and the shear stress in pin

Q: The piece of wood shown below was used in an experiment. During the test it sheared parallel to the…

A: Given:P=1750 lbt=2.5 inL=5 in

Q: The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each…

Q: The hanger is supported using the rectangular pin. Determine the magnitude of the allowable…

A: Given that: The allowable bearing stress σb=220 MPa The allowable tensile stress σt=150 MPa The…

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

Q: The structure shown supports a distributed load of 700 Ib/ft. Assume a - 4.1 ft b-1.0 ft. c-2.1 ft,…

Q: 4. The frame is subjected to the load of 15 kN which acts on member ABD at D. Determine the required…

Q: 1. The structure is used to support a distributed load of w = 15 kN/m. The bolts at A, B, and C each…

Q: 1.39 The bar AB is supported by a frictionless inclined surface at A and a 7/8- in.-diameter pin at…

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

Q: Two pieces of wood, 2 in. by 4 in., are glued together along the 40° Joint. Determine the maximum…

Q: the pins at A and B if the allowable normal stress for member BC is Oallow = 35 ksi and the…

A: Handwritten.jpg

Q: The pin for the hinge support the allowable shear stress is 200 Mpa. Design the diameter of the pin…

A: Given:ζ=200 MPaTo determine the diameter of the pin

Q: Q4/ The aluminum bracket A is used to support the centrally applied load of 8 kip. If it has a…

A: Given Data The Factor of safety, fos=3.0 The centrally applied load, P=8 kip the constant…

Q: Solve Prob. using the maximum shear stress theory.

A: Given data: Stress in horizontal direction is σx = 20 ksi. Stress in vertical direction is σy = -12…

Q: rod A 2m. 2m. 60°

Q: Members A and B are made of wood and have a thickness t = 6 mm. If member B is subjected to a…

Q: The hanger at B is held by 10 nails against a column. Determine (a) the shear force, V (in N)and (b)…

Q: 800 N 45mm 800 N 9. The lapbelt assembly is to be subjected to a force of 800 N. Determine the…

Q: Current Attempt in Progress Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie…

Q: Compute the maximum force P in Newtons that can be applied to the foot pedal. (Express your answer…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given: Let us consider the given data, d=0.75P=56 kipsn=5 Where, d=Diameter P=Applied load n=Bolt…

Q: 1-55: In the structure shown, an 8 mm diameter pin is used at A, and 12-mm- diameter pins are used…

A: Given Data Pin diameter at, A= 8mm Pin diameter at, B= 12mm shear stress, τ=100 MPa Ultimate…

Q: The joint is fastened using two bolts. Determine required diameter of the bolts if the failure shear…

Q: The hanger is supported using the rectangular pin. Determine the required thickness t of the hanger,…

Q: 4. The frame is subjected to the load of 15 kN which acts on member ABD at D. Determine the required…

Q: Q15: The frame is subjected to the load of 4 kN which acts on member ABD at D. Determine the…

A: AS PER COMPANY POLICY, ONLY ONE QUESTION CAN BE SOLVED AT A TIME. FOR SOLUTION OF OTHER QUESTIONS,…

Q: The rigid wrench (not the brand Rigid sold at Home Depot!) shown is used to loosen a stuck nut at…

Q: 1.36 The bell crank, which is in equilibrium under the forces shown in the figure, is supported by a…

A: To find diameter of rod AB and stress in pin at D

Q: Q9): If the pins D and C are subjected to single shear while pin at A is a double shear. The…

A: For the given arrangement dia of pins at D, C, A is 1.5in. ,1.5in. , and 1 in. Dia of bar DC =…

Q: Q-1 Two wrenches are used to tighten the pipe. If P = 350 N is applied to each wrench, determine the…

Q: The bar AB is supported by a frictionless inclined surface at A and a % in diameter pin at B that is…

Q: Question 3 The frame is subjected to the load of 4 kN which acts on member ABD at D. Determine the…

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

A: Given data Diameter of steel shaft = 30 mmAllowable shear stress = 120 MPaAngle of twist = 7°Shear…

Q: The assembly is used to support a distributed loading of w = 6.6 kN/m. The solid steel rod BC has a…

Q: The cotter is used to hold the two rods together. Determine the smallest thickness t of the cotter…

A: Given, PN = 30 kN = 30000 N PS = 30 kN = 30000 N (F.S)t = 2.5 (F.S)s = 1.75 σfail = 500 MPa = 500…

Q: The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the…

A: Given data: The allowable bearing stress of the washers on the boards, (σb)allow = 2 ksi. The…

Q: Q2) The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. If the…

A: Given data:- Internal radius, r1=25 mm Outer radius, r2=40 mm

Q: 3) With a given load P = 22.5 kips, two 2 in x 4 in wooden joints are glued together along the joint…

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

Q: 1.38 The right-angle bar is supported by a pin at B and a roller at C. What is the maximum safe…

A: Given:ζ=20,000 psid=34 in

Q: The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each…

Q: 30 mm - 80 kN 30 mm 2. The joint is fastened together using two bolts. Determine the required…

Q: If the allowable tensile stress for the bar is (ot)allow = 22.6 ksi, and the allowable shear stress…

Q: The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of…

Q: 6. The bar AB is supported by a frictionless inclined surface at A and a 7/8-in.- diameter pin at B…

A: GIVEN DATA- DIAMETER OF PIN d=7/8in. VERTICAL LOAD =2000lb WE HAVE TO FIND SHEAR STRESS AT PIN

Q: Situation 1: A flexible cable and rigid boom system is used to liflt a load of 65KN at the end of…

A: Draw the free-body diagram of boom system.

Q: Part A The beam is supported by a pin at A and a short link BC. If P = 12 kN , determine the average…

Question

#2 The joint is fastened together using two bolts. Determine the required diameter
of the bolts if the shear stress failure for the bolts is Tau = 350MPA. Use a Factor of
Safety for Shear of F.S. = 2.5. Set up your FBD and forces on bolts correctly i
Tip: F.S. =
80 kN
30 mm-
30 mm
40 kN
40 kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A simple truss is subjected to a vertical load F = 500 lb.Determine the minimum diameter of the pin at C if theallowable shear stress on the pin is 20 psi.Answers: d =___________________
Design the diameter of the pin for the hinge supportif the allowable shear stress is 250 Mpa.
The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
Two bolts are used to lap joints two steel plates. The tensile force on the plate is 40 kN. Determine the required diameter of the bolts if the failure shear stress of the bolts is 350 MPa. Use a factor of safety for shear equal to 2.5.
Determine the required diameter of the pins at A and B if theallowable shear stress for the material is tallow = 100 MPa.Both pins are subjected to double shear.
(D) The pin used at B has an ultimate shear strength of 58 ksi. If a factor of safety of 2.5 is required, determine the allowable shear stress in this pin. in ksi (E) The pin used at B is a double shear pin connection. Determine the minimum pin cross-sectional area, and the corresponding minimum pin diameter that can be used at B. (Amin IN in.2 and dpin IN in.) (F) Determine the deformations in rods (1), (2), and (3) when load P equals Pmax from Letter C. ANSWERS in inch (G) Using the results from Letter F, determine the deflections of Joint B and Point D. ANSWERS in inch
The pin-connected frame supports the loads P1 = 5 kN and P2 = 10 kN. Determine for an angle of α = o0 : (a) The normal stress in the bar EC of uniform cross-sectional area 15 x 10-5 m2 . (b) The shearing stresses in the 10 mm diameter pins at D and E if both are in double shear.
Consider the wooden member subjected to a tensile load P = 11.00 kN. Determine the shear stress at the inclined section as shown.
The stepped steel shaft carries the torque T. Determine the allowable magnitude of T if the working shear stress is 22 MPa and the and the rotation of the free end is limited to 5.2°. Use G = 83 GPA. Show the free body diagram.
The stepped steel shaft carries the torque T. Determine the maximum allowable magnitude of T if the working shear stress is 14 MPa and the rotation of the free end is limited to 3.50 . Use G = 83 GPa for steel
The lap joint is fastened by 5 one-inch diameter rivets. For P = 10 kips, determine (1.) the maximum shear stress in the joints, (2.) the maximum bearing stress in the rivets, and (3.) the maximum stress at section a-a.
The axial stresses are 12 MPa C in the wood post B and 150 MPa T in the steel bar A as shown below. Pins at A, C, and D are smooth. Determine (a)The load P.(b)The minimum diameter for pin C if it is in single shear and the cross-shearing stress is limited to 70 MPa.(c)The minimum diameter for pin D if it is in double shear and the cross-shearing stress is limited to 70 MPa.