2. For a piping system as shown in the figure, determine the distribution of the water flow Qi and the piezometric height H at the junction. The powerof the pump is YQH, = 20 kW. constant, equal to inputAssume the friction factor is constant el 30 m Pipe L (m) D (m) EK el 15 m 50 0.15 1 121 0.02 0.015 0.025 el 10 m [2] 100 300 0.10 0.10 1 1 P [1] B [3] 123

2. For a piping system as shown in the figure, determine the distribution of the water flow Qi and the piezometric height H at the junction. The powerof the pump is YQH, = 20 kW. constant, equal to inputAssume the friction factor is constant el 30 m Pipe L (m) D (m) EK el 15 m 50 0.15 1 121 0.02 0.015 0.025 el 10 m [2] 100 300 0.10 0.10 1 1 P [1] B [3] 123

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two identical pumps are connected in series and deliver water through an 45cmdiameter, 2.2km long, commercial steel pipe from reservoir A (surface elevation = 50m) to reservoir B(surface elevation = 100m). Consider minor losses of a square-edged inlet, exit, and swing-type checkvalve. Determine the discharge, the total head added by the pumps, and the total power output. The pumpcharacteristics for a single pump is tabulated below. Assume that the kinematic viscosity is 1x10-6 m 2/s and a specific weight of 9.79kN/m 3 . Plot the system and pump characteristic curves on a single plot. Besure to label the axes appropriately (i.e., include units). Be sure to include a legend to demark the systemhead curve and the pump characteristic curve.
Water flows at 20°C through a new cast iron pipe at a velocity of 4.2 m/s. The pipe is 400 m long and hasa diameter of 150 mm. Determine the head loss due to friction. Ans. 54.20 m (show the complete solution) Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet. E.g. (density, viscosity)Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness
Determine the head loss due to friction of an oil of specific gravity 0.77 and viscosity 0.85 poise is flowing through a pipe at the rate of 3.7 m/s. Assume the pipe diameter as 29 cm and the length of the pipe as 5618 cm. Oil Density (in kg/m3) Reynold's Number - Co-efficient of friction - Head loss due to friction
Three pipes connected in series with lengths L1 = L2 = L3 = 150 m and diameters D1 =75 mm, D2 = 50 mm, D3 = 25 mm. The discharge at the 25mm pipe = 200 lps, kinematic viscosity = 1.12 x 10-6 m2/s and ε = 0.35 mm. Using Colebrook and Darcy-Weisbach Formula, determine the following:a. relative roughness of the 25mm pipeb. roughness coefficient of 75mm pipec. head loss of 50 mm pipe
The flow rate of water in a garden hose is measured using the bucket-andstopwatch method. Filling a 5-L bucket takes 75 seconds. If the inner diameter of the hose is 10 mm and the density and viscosity of water are approximately 998 kg m-3 and 0.9 cP, respectively, (a) is the flow inside the hose laminar or turbulent? (b) If the flow rate is adjusted such that the flow is with Re = 2100, how long would it take to fill the same bucket?
The present pumping rate of crude oil through the AlaskaPipeline, with an ID of 48 in, is 550,000 barrels per day(1 barrel = 42 U.S. gallons). (a) Is this a turbulent flow?(b) What would be the maximum rate if the flow wereconstrained to be laminar? Assume that Alaskan oil fitsFig. A.1 at 60°C.
A 25cm circular pipe carries 0.16m3 /sec of water under a pressure of 200Pa. The pipe islaid at an elevation of 10.71m above the mean sea level (MSL) of Ibadan. What is theenergy head measured with respect to the MSL? If = 9810N/m3 (9.81KN/m3).
The rate of flow of water in a 150 mm diameter is measured with a venturi meter with a 50 mm diameter throat. When the pressure drop over the converging section is 121 mm of water, the flow rate is 2.91kg/s. What is the coefficient for the converging cone of the meter at this flow rate?A. 0.81B. 0.985C. 0.90D. 0.745
what is the pressure drop per meter for water flowing at 6 m/s through a 8 x 4 cm annulus? (dinner = 4 cm , douter = 8 cm)
Determine the pressure drop over a reducer with the following conditions: Fluid density: 25 kg/m3Fluid velocity: 1.5 m/sFluid viscosity: 0.001 Pa*sInlet diameter: 0.12 mOutlet diameter: 0.019 mPipe absolute roughness: 4e-4 m Give your final answer in Pa, rounded to the nearest whole number. [Ignore entrance/exit losses and velocity loss terms]
A petroleum product of viscosity 0.5 m Ns/m2 and density 700 kg/m3 is pumped througha pipe of 0.15 m diameter to storage tanks situated 100 m away. The pressure drop alongthe pipe is 70 kN/m2. The pipeline has to be repaired and it is necessary to pump the liquid by an alternative route consisting of 70 m of 200 mm pipe followed by 50 m of 100 mm pipe. If the existing pump is capable of developing a pressure of 300 kN/m2, will it be suitable for use during the period required for the repairs? Calculate the pressure drop for the alternative pipe system. Take the roughnessof the pipe surface as 0.05 m
The reservoirs in Fig. are connected by cast iron pipesjoined abruptly, with sharp-edged entrance and exit. Includingminor losses, estimate the flow of water at 20 °C if the surfaceof reservoir 1 is 45 ft higher than that of reservoir 2.