2. The grooved drums in two systems shown are identical with masses of 14 kg, ko = 225 mm, r, = 325 mm, and r; = 215 mm. In both cases (a) and (b) the system is at rest at time t= 0. Find the angular velocity of each system after 4 s. m. 10(9.81) N 10 kg (a) (b)

2. The grooved drums in two systems shown are identical with masses of 14 kg, ko = 225 mm, r, = 325 mm, and r; = 215 mm. In both cases (a) and (b) the system is at rest at time t= 0. Find the angular velocity of each system after 4 s. m. 10(9.81) N 10 kg (a) (b)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Prove the relation that Hammer blow = ± mb x r*x ω2 where mb = Balancing mass placed at a radius of r* and ω= angular speed of the crank.
In the figure shown, the hydraulic cylinder moves upwards with a constant speed of Va=0.2 m/s, transferring vertical movement to corner A of the container. If bearing b never slips and has a diameter of 8 cm, determine the angular velocity of the imaginary line drawn from its axis of rotation to any point on its periphery. Determine the angular velocity of side CD at this moment.
In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
Answer the question in full details, thank you very much: A spherically symmetric object, with radius R = 0.70 m and mass M = 1.5 kg, rolls without slippingacross a horizontal floor, with velocity V = 3.0 m/s. It then rolls up an incline with an angle of inclinationAngle = 44 deg and comes to rest a distance d = 0.92 m up the incline, before reversing direction and rollingback down. Find the moment of inertia of this object in kg-m^2 about an axis through its centre of mass.
A drum of mass Ma and radius a rotates freely withinitial angular velocity ωa0. A second drum with mass Mb and radiusb > a is mounted on the same axis and is at rest, although it is free torotate. A thin layer of sand with mass Ms is distributed on the innersurface of the smaller drum. At t = 0, small holes in the inner drumare opened. The sand starts to fly out at a constant rate λ = dm/dtand sticks to the outer drum. (a) Explain, in detail, why the angularvelocity of the inner drum will remain constant. (b) Determine theangular velocity of the outer drum ωb(t). Ignore the transit time ofthe sand
A 18-kg rear hatch of a vehicle opens as shown in the figure and can be modeled as a uniform 0.6-m long slender rod. Knowing that the tailgate is released from rest in the position shown in the figure, determine the angular velocity of the tailgate as it impacts the car body. I have attached Solution Too, You can Refer It( There Mass=16 kg) In our Problem Mass=18 Kg That is Only difference.
A particle M1, weighing 2.4 Ibs, is tied to a thread and describes a circular path in a horizontal plane. The thread, of negligible mass, passes through a hole in the center of the circle and descends vertically. Another particle M2 is attached, weighing 5.0 Ibs, as shown in the figure. If M1 describes a uniform circular motion, with angular velocity w 3.1 rad/s, determine the radius R of the circumference in inches.
Consider a slender rod AB with a length l and a mass m. The ends are connected to blocks of negligible mass sliding along horizontal and vertical tracks. If the rod is released with no initial velocity from a horizontal position as shown in Fig.A, determine its angular velocity after it has rotated through an angle of θ (see Fig B) using the conservation of energy method. (Hint: Moment of inertia of rod about G = (1/12)ml2 The kinetic energy of a rigid body in plane motion is
A uniform crate C with mass m is being transported to the left by a forklift with a constant speed v1 . What is the magnitude of the angular momentum of the crate about point D , that is, the upper left corner of the crate?a. 0b. mv 1ac. mv 1 bd. mv 1
Lever is attached to a gear of radius R_1 = 0.50 in and moment of inertia I_1 = 1.0 kg m^2. This gear meshes with a second gear of radius R_2 = 1.0 m and moment of inertia I_2 = 16.0 kgm^2. Each gear rotates about a fixed axis running through its center. Force F = 2.0 N is applied on the lever at a distance of 1.0 m from the center of the gear. What is the angular acceleration of each gear?
The connecting rod of a horizontal reciprocating engine is 400 mm and length of the stroke is 200mm. The mass of the reciprocating parts is 125 kg and that the connecting rod is 100 kg. The radius of gyration of the connecting rod about an axis through the centre of gravity is 120 mm and the distance of centre of gravity of the connecting rod from big end centre is 160 mm. The engine runs at750 r.p.m. Determine graphically the torque exerted on the crankshaft when the crank has turned 30° from the inner dead centre.
A rotating shaft carries four unbalanced masses 18 kg, 14 kg, 16 kg and 12 kg at radii 50 mm, 60 mm, 70 mm and 60 mm respectively. The 2nd, 3rd and 4th masses revolve in planes 80 mm, 160 mm and 280 mm respectively measured from the plane of the first mass and are angularly located at 60°, 135° and 270° respectively measured clockwise from the first mass.The shaft is dynamically balanced by two masses, both located at 50 mm radii and revolving in planes mid-way between those of 1st and 2nd masses and midway between those of 3rd and 4th masses. Determine, balancing mass by drawing couple polygon and their respective angular position graphically.