(4) What pressure drop is required in order to pump water at 20'C through a pipe 25 cm in diameter and length 1234 m at a rate of 1.97 m² sec"? The pipe is horizontal and contains four standard-radius 90" elbows and two 45' elbows. (A standard-radius 90" elbow is roughly equivalent to the resistance offered by a pipe of length 32 diameters; a 45' elbow, 15 diameters)

(4) What pressure drop is required in order to pump water at 20'C through a pipe 25 cm in diameter and length 1234 m at a rate of 1.97 m² sec"? The pipe is horizontal and contains four standard-radius 90" elbows and two 45' elbows. (A standard-radius 90" elbow is roughly equivalent to the resistance offered by a pipe of length 32 diameters; a 45' elbow, 15 diameters)

Name: roughness of this plastic.(4) What pressure drop is required in order
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: roughness of this plastic.(4) What pressure drop is required in order to pump water at 20'C through a pipe 25 cm indiameter and length 1234 m at a rate of 1.97 m² sec!? The pipe is horizontal andcontains four standard-radius 90" elbows and two 45" e

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 25cm circular pipe carries 0.16m3 /sec of water under a pressure of 200Pa. The pipe islaid at an elevation of 10.71m above the mean sea level (MSL) of Ibadan. What is theenergy head measured with respect to the MSL? If = 9810N/m3 (9.81KN/m3).
Considering pipe loss only, how much head is required to deliver 0.222 m³/s of heavy fuel oil at 38°C through 914 m of new cast iron pipe, 300 mm inside diameter? Use ε=0.00024 m. (ANSWER MUST BE = 41 m)
The pipe fl ow in Fig. is driven by pressurized air inthe tank. What gage pressure p1 is needed to provide a 208Cwater flow rate Q = 60 m3/h?
The spiral conical draft tube are connected to Francis turbine. The diameters of the internal and external of tube are equal to 60 cm and 90 cm respectively. The tube should be drowned-approximately 1.5 meter below the lowest tail race level and draft tube high of 600 cm. The velocity at the exit is 1.5 meter per second. (Friction head loss in draft tube = 0.034 m ), calculate:- Find the pressure head at the entrance and the bottom in m of water and in Kg / cm?. the total heads at the same point with reference to the tail race as a datum find the power at the entrance and bottom the efficiency of a draft tube
It is desired to deliver 60 m3/h of water at 20°C through ahorizontal asphalted cast iron pipe. Estimate the pipe diameterthat will cause the pressure drop to be exactly 40 kPaper 100 m of pipe length.
In a pipe of diameter 300mm the center line velocity and the velocity at a point 100mm from the center, as measured by pitot tube are 2.4 m/s and 2.0 m/s respectively. Assume the flow in the pipe to be turbulent find: 1-Dischrge through the pipe,2-Coefficient of friction, 3 Height of roughness projections.Please do not waste my question solve with correct answers only.
Two reservoirs, which differ in surface elevation by 40 m,are connected by a new commercial steel pipe of diameter8 cm. If the desired flow rate is 200 N/s of water at 20°C,what is the proper length of the pipe?
A pump delivers 1 hp to a water at 68°F flowing in a 10-in-diameter horizontal, cast iron pipe at V = 6.6 ft/s. Estimate the proper pipe length (in feet) that will match these conditions. For water at 68°F: ρ = 1.94 slug/(ft^3), and μ = 2.09E-5 slug/(ft-s). Assume also that the head added by pump matches the head loss. Round your answer to 2 decimal places.
A pipe 100mm bore carries oil of density 900 kg/m3 at a rate of 4 kg/s. thepipe reduces to 60mm bore and rises 120m. the pressure at this point isatmospheric (zero gauge) assume no frictional losses.Determine:The volume per secondThe velocity at each sectionThe pressure at the lower end The above pipe is exchanged for a parallel pipe with a cross sectional area of 0.3m2 and is 20 m long, with a surface roughness coefficient of 0.005. The dynamicviscosity of the water is 1.002 x 10-3 Ns/m. Find the Reynold’s number of the flowand use Haarland’s formula to find the friction coefficient and Darcy’s formula todetermine the frictional pressure loss. Then determine the pressure at the outlet ofthe pipe.What does the magnitude of the Reynolds number mean to fluid flow
Two reservoirs, which differ in surface elevation by 40 m,are connected by 350 m of new pipe of diameter 8 cm. Ifthe desired flow rate is at least 130 N/s of water at 20°C,can the pipe material be made of (a) galvanized iron,(b) commercial steel, or (c) cast iron? Neglect minor losses.
What is the Reynolds number for a straight and perfectly smooth pipe of length 500 m and diameter 0.2 m, transporting oil (density 900 kg/m3 and viscosity 0.5 Pa-s) at a flow rate of 100 kg/s from sea level to an elevated height 10 m above sea level? What is the viscous pressure drop along the pipe?
The system consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water into the reservoir? Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kvalve = 6.9 f = 0.0316 γ = 9810 N/m3 Choices: 3.44 Mpa 1.02 MPa 3.48 Mpa 1.00 MPa None of the choices