Answered: 5.10 The zero sequence current of a…

5.10 The zero sequence current of a generator for line to ground fault is j2.4 p.u. Then the current through the neutral during the fault is (b) j0.8 p.u. (d) j0.24 p.u. (a) j2.4 p.u. (c) i7 2 pu.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter9: Unsymmetrical Faults

Section: Chapter Questions

Problem 9.4MCQ

See similar textbooks

Related questions

Q: Line to ground fault has the highest probability in the power system O True False

A: Need to find true false

Q: Three zones of a single-phase circuit are identified in Figure. The zones are connected by…

A: per unit system The ratio of actual value to the base or reference value in the same unit is called…

Q: Q2. Explain the symmetrical fault analysis using ZbuS.

A: Note: As per the guidelines will be solving only 1st question. Repost for others Symmetrical fault…

Q: What is load line and what is duty cycle?

Q: 3.On a double line-to-ground faultImmersive reader A) The short-circuit currents in the faulted…

A: In this question , we will write about double line to ground fault....

Q: Q1/ Equipment ratings for the four-bus power system shown in Figure are as follows: Generator G1:…

Q: Problem 5 Consider the system shown in the single-line diagram of Figure (3). All reactances are…

A: Single Line Diagram: A single-line diagram, often known as an SLD, is an electrical diagram or…

Q: In a three phase overhead system, each line is suspended by a string of three insulator. The voltage…

Q: In the figure below, all impedances are in per unit on a common MVA base. The generators are…

Q: For the circuit shown, the normal operating values shown are known. If a symmetrical three-phase…

A: We can redraw the per-phase equivalent circuit as

Q: Under Unbalanced Condition With Faults: a. Load Line Currents (la, Ip,!c); b. Load Line Voltages…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: What are the wind turbine losses? How to minimize these losses? What is the role of SCADA system in…

A: Wind turbine losses: There will be electrical losses practised between the low voltage terminals of…

Q: Define percentage line and load regulation

A: Line regulation-Line regulation refers to a power supply's capacity to maintain a constant output…

Q: In a power system the fault is occurred in all the lines and to the ground without fault impedance…

A: all the line and to the ground fault is symmetrical fault.

Q: Calculate the initial symmetrical short circuit current that will occur when a 3 phase short circuit…

A: We can re draw the given system as Let the base MVA of the system i.e SB 500MVA and base Voltage…

Q: Problem 6 a- Explain the reasons for applying system grounding in electric power systems. Consider…

A: The current flowing through a circuit during a fault condition is called fault current. Fault types…

Q: I. Draw the reactance diagram for the following power system in per unit using base power = 50 MVA…

Q: The LLLG fault occurs at bus-6 with pre-fault voltage as 1.05 p.u. If the positive sequence…

A: Given, The pre-fault voltage at bus-6 is V6 = 1.05 pu Positive sequence impedance at bus-7 is Z7 =…

Q: The per unit bus impedance matrix for the power system network of Figure Q1 is given by; [0.240…

A: 1. Fault current Zf=j0.0225fault at Bus 2If2=VthZbb+ZfIf2=1Z22+Zfputting the value of Z22 from the…

Q: The zero sequence impedance offered by the equipment to flow of .............equence currents.

A: For any equipment, The impedance offered by the system to the flow of zero sequence current is known…

Q: For grounded systems, the _ for the service and the system bonding jumper for separately derived…

A: The equipment grounding conductor connections at the source of separately derived systems are done…

Q: a. In sequence networks of power system, why does voltage sources appear only in the positive…

A: a) Machine are design such as it will generate voltage if the phase sequence will be same as…

Q: Problem 5: Thevenin equivalent sequence networks looking into the faulted bus of a power system are…

Q: The one-line diagram of a power system is shown in the figure below. A single-line-to- ground (SLG)…

A: A single line to ground fault occurs at bus 2. So the fault current will be- Ea=Genetaror terminal…

Q: Discuss with block diagram, the principle of operation of single phase energy met

A: (i provide you the solution in RULE PAPER for easily understand to the diagram and its related…

Q: The one line diagram of a simple three bus power system is shown in figure Each generator is…

A: The fault occurred on bus 3 is a three phase fault. Three phase fault is a balanced fault (All…

Q: The one-line diagram of a simple power system is shown in the figure. The neutral of each generator…

Q: Briefly explain the functions of smart grid.

Q: When a 40 MVA, 13KV, 3 – phase generator is subjected to a 3 – phase fault, the fault current is j4…

A: The solution is given below

Q: For the system shown in figure Q5. а. Determine the three-phase fault power (in MVA) and the short…

A: Base MVA= 20MVA Per unit reactance of all the generators: Per unit reactance of transformers:

Q: Some electricians do not bother to calculate the minimum size of neutral service conductor. They…

A: 3-phase star connection balanced system does not require a neutral wire in the system. Basically, in…

Q: Deviations in quality of service include power irregularities. Which irregularity occurs when…

A: This problem is from power system. The solution is given below.

Q: B) State the main points that should be taken in to account in selection of number and sizes of the…

A: B) The main points that should be taken into consideration while selecting the number and the sizes…

Q: Figure 6.12 shows the one-line diagram of a simple three-bus power system with generators at buses 1…

Q: The zero-, positive-, and negative-sequence bus impedance matrices for a two-bus three-phase power…

Q: j0.2 For the following power system the impedance matrix is given below. Initially all bus voltages…

Q: The zero sequence currents of a generator for line to ground fault is j2.4 p.u. then the current…

Q: Q1. A// Choose the correct answer: 1. One of the advantage of using a per unit system in power…

A: According to guidelines we are allowed to do only first 3 questions , please post again for…

Q: The making current of 3-phase breaker with rating 2000 MVA, 33 kV will be

A: Given, Power rating, S = 2000 MVA Voltage rating, V = 33 kV

Q: The reactance information of the power network is shown in the figure, in units of common base. The…

Q: How do I convert the following per unit voltages to actual voltage

A: In this question base voltage given, and per unit voltage is given.....We have to find out actual…

Q: 6.1. A power system network is shown in Figure 47. The generators at buses 1 and 2 are represented…

A: The power system network is shown below,

Q: 5.2 Balanced Three-phase Fault Example 5.1 Determine the fault current, the bus voltages, and…

A: When all three lines are shorted to ground, this is known as a balanced (or three phase) fault. It…

Q: A three-bus power system has generators at buses 1 and 2 with per unit subtransient reac- cances…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 1- Which of the following is true in decoupled load flow method a- Jacobians J1 and J2 are…

Question

5.10 The zero sequence current of a generator for line
to ground fault is j2.4 p.u. Then the current through
the neutral during the fault is
(a) j2.4 p.u.
(b) j0.8 p.u.
(d) j0.24 p.u.
(c) i7.2 p.u.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Derive an expression of per unit impedance of a given base MVA and base KV in term of new base MVA and new base KVA
Contribution of fault analysis in power system netwrok?
Line to line to line fault is an asymmetrical type of fault in power system which occurs very frequently true false
Equipment ratings for the four-bus power system shown in Figure 7.14 are as follows: Generator G1: 500 MVA, 13.8 kV, X=0.20 per unit Generator G2: 750 MVA, 18 kV, X=0.18 per unit Generator G3: 1000 MVA, 20 kV, X=0.17 per unit Transformer T1: 500 MVA, 13.8/500YkV,X=0.12 per unit Transformer T2: 750 MVA, 18/500YkV,X=0.10 per unit Transformer T3: 1000Â MVA, 20/500YkV,X=0.10 per unit A three-phase short circuit occurs at bus 1, where the prefault voltage is 525 kV. Prefault load current is neglected. Draw the positive-sequence reactance diagram in per unit on a 1000-MVA, 20-kV base in the zone of generator G3. Determine (a) the ThĂ©venin reactance in per unit at the fault, (b) the subtransient fault current in per unit and in kA rms, and (c) contributions to the fault current from generator G1 and from line 1-2.
Consider the oneline diagram of a simple power system shown in Figure 9.20. System data in per-unit on a 100-MVA base are given as follows: The neutral of each generator is grounded through a current-limiting reactor of 0.08333 per unit on a 100-MVA base. All transformer neutrals are solidly grounded. The generators are operating no-load at their rated voltages and rated frequency with their ENIFs in phase. Determine the fault current for a balanced three-phase fault at bus 3 through a fault impedance ZF=0.1 per unit on a 100-MVA base. Neglect -Y phase shifts.
Some line transients are not damaging to electronic equipment but can cause the equipment to operate improperly. The effects of these transients can be minimized by installing _________________
Figure 3.39 shows a oneline diagram of a system in which the three-phase generator is rated 300 MVA, 20 kV with a subtransient reactance of 0.2 per unit and with its neutral grounded through a 0.4- reactor. The transmission line is 64km long with a cries reactance of 0.5-/km. The three-phase transformer T1 is rated 350MVA.230/20kV with a leakage reactance of 0.1 per unit. Transformer T2 is composed of three single-phase transformers, each rated 100 MVA, 127/13.2kV with a leakage reactance of 0.1 per unit. Two 13.2kV motors M1 and M2 with a subtransient reactance of 0.2 per unit for each motor represent the load. M1 has a rated input of 200 MVA with its neutral grounded through a 0.4- current-limiting reactor, M2 has a rated input of 100 MVA with its neutral not connected to ground. Neglect phase shifts associated with the transformers. Choose the generator rating as base in the generator circuit and draw the positive-sequence reactance diagram showing all reactances in per unit.
3.On a double line-to-ground faultImmersive reader A) The short-circuit currents in the faulted phases are equal. B) The voltages at the fault point on the faulted phases are zero. C) The phase not involved in the fault has a zero voltage at the fault point. D) There are no circulating currents through the neutrals to ground. E) N. A.
There is no zero sequence component in line to line fault.Select one:O TrueO False
answer both i will rate.... a. In sequence networks of power system, why does voltage sources appear only in the positive sequence? b. Describe the main differences in fault protection objectives when dealing with a temporary fault vs a permanent fault.
Three zones of a single-phase circuit are identified in Figure. The zones are connected bytransformers T1 and T2, whose ratings are also shown.Using base values of 30 kVA and 240 volts in zone 1:a. draw the per-unit circuit and determine the per-unit impedances and the per-unitsource voltage.b. calculate the load current both in per-unit and in amperes. Transformer windingresistances and shunt admittance branches are neglected.
For the circuit shown, if a symmetrical three-phase fault occurs in node 2, determinea. The short-circuit current in all three phases. b. The voltage at node 1 during the fault.c. The current in generator 1 during the fault. Neglect the prefault currents and consider the reference voltage of the system at 10√3 ??.