A 20mm thick plate Fy = 250 Mpa, Fu = 415 Mpa, has 20mm nominal bolt holes. Using ASD and LRFD (NSCP2015), the following apply. For tensile yiielding on gross section : Pn = Fy Ag, reduction factor = 0.90 (LRFD), factorof safety = 1.67 (ASD). For tensile ruptureof safety = 2.00 (ASD). Determine the tension iin yielding capacity and tension rupture capacity of the connection.net area section : Pn = Fu Ae , reduction factor = 0.75 (LRFD) , factor5037.5375755050505037.5 375 37537.5 37.5 37.5

Answered: Image /qna-images/answer/a277a84a-52b7-4aa2-90a6-d700d198abb2.jpg

A 20mm thick plate Fy = 250 Mpa, Fu = 415 Mpa, has 20mm nominal bolt holes. Using ASD and LRFD (NSCP 2015), the following apply. For tensile yiielding on gross section : Pn = Fy Ag, reduction factor = 0.90 (LRFD), factor of safety = 1.67 (ASD). For tensile rupture in net area section : Pn = Fu Ae , reduction factor = 0.75 (LRFD), factor of safety = 2.00 (ASD). Determine the tension iin yielding capacity and tension rupture capacity of the connection. 75 37.5 375 50 50 50 50 37.5 37.5 37.5

A 20mm thick plate Fy = 250 Mpa, Fu = 415 Mpa, has 20mm nominal bolt holes. Using ASD and LRFD (NSCP 2015), the following apply. For tensile yiielding on gross section : Pn = Fy Ag, reduction factor = 0.90 (LRFD), factor of safety = 1.67 (ASD). For tensile rupture in net area section : Pn = Fu Ae , reduction factor = 0.75 (LRFD), factor of safety = 2.00 (ASD). Determine the tension iin yielding capacity and tension rupture capacity of the connection. 75 37.5 375 50 50 50 50 37.5 37.5 37.5

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cap screw, ¾ in.-10-UNC-2, with a hexagonal head that is 9/16 in. thick, carries a tensile load of 3000 lb. If the material is AISI 1015, cold drawn, find the factor of safety based on ultimate strengths of a.the threaded shank, b.the head against being sheared off, and c.the bearing surface under the head. d.Is there any need to consider the strength of standard cap-screw heads in design?
Define the rigid body used in statics. According to this; rigidity of bolt-nut connected elementBased on the value, the bolt diameter is 20 mm and the safe value of the bolt material.Calculate the stiffness values of the bolt and the intermediate element plate. (Note: Bolt's9x10 ^ 2 times as stress value ??? / cm ^ 2take as.). Strain gaugeElongation in bolt length measured with 250 ??, shortening amount in intermediate element platesIt was measured at 125 ??.
Two 1/4 in × 8 in A36 steel plates are joined with a lap joint using 3/4 in A325-N bolts. If a concentric unfactored live load of 50 kips (dead load = 0) is required to be resisted by the connection and the bolt shear strength controls the design, the minimum required number of bolts is?
An ASTM cast iron, grade 30, has ultimate strength at tension Sut = 350 MPa, and at compression Suc = 1150 MPa. it carries static loading resulting in the stress state listed below at the critical locations. Using the static failure analysis estimate the factor of safety. σA = 127 MPa, σB = -264 MPa.
An M30 × 3.5 ISO grade 8.8 bolt is used in a joint at a preload levelrecommended for reused connections, and the joint is subject to a repeated tensilefatigue load of P = 65 kN per bolt. The joint constant is C = 0.25.a) Determine the static load factors; b) The factor of safety guarding against a fatigue failure based on the Goodmanfatigue criterion
A M20 × C4 bolt of mild steel is having yield stress of 320 MPa and factor of safety 3. The safe static tensile load in kN will be
A hollow, short compression member, of normalized cast steel (ASTM A27-58, 65 ksi), is to support a load of 1500 kips with a factor of safety of 8 based on the ultimate strength. Determine the outside and inside diameters if Do = 2Di
Determine the safe tensile load for fine series bolts of (a) M 24and (b) M 38. Assume that the bolts are not initially stressed and take the safe tensile stress as 450MPa.
An ASTM cast iron, grade 30, has ultimate strength at tension Sut = 358 MPa, and at compression Suc = 1,000 MPa. it carries static loading resulting in the following principle stress σA = 123 MPa , σB = -259 MPa. Choose the appropriate failure theory and estimate the factor of safety.
Which of the following is the design stress for a piston rod where the axial load is completely reversed if the surface of the rod is ground and the surface finish factor is 0.9? Assume no stress concentration. Use a factor of safety of 2 and an endurance limit of 250 MPa. The load factor for completely reversed axial load is 0.85.
A rectangular bar is cut from an AISI 1018 cold-drawn steel flat. The bar is 1 in wide by 3/8 in thick and has a ¼ in-diameter hole drilled through the center. The bar is subjected to a tension load fluctuating between 800 and 3000 lb. estimate the factors of safety guarding against failure by yielding and by fatigue action. (Assume infinite life is desire)
A round steel rod made of structural steel, AISI C1118, As rolled is to be used as a column, centrally loaded with 15 kips; N= 2.75. Determine the diameter for (a) L= 20 in. (b) L= 5 in. (c) the same as (a) and (b) except that the material is AISI 9850, OQT 1100 F. Is there any advantage in using this material rather than structural steel?