A cube shaped smooth steel block with size a = 5 cm is released on a smooth inclined surface which makes an angle of a = 15° with the horizontal. There is an olive oil layer between the block and inclined surface with thickness Ay = 0.1mm. Draw this configuration properly and discuss briefly what will happen when the block is released. Show the forces acting on the sliding block when the velocity of the block is constant (dlosk = 0) and write down the force equation for the axis parallel to inclined surface (ignore the resistance due to air). Draw the linear velocity distribution across the thin layer of oil between the block and the inclined surface. Perform an internet search for the specific weight of steel (7steel) and the dynamic viscosity

A cube shaped smooth steel block with size a = 5 cm is released on a smooth inclined surface which makes an angle of a = 15° with the horizontal. There is an olive oil layer between the block and inclined surface with thickness Ay = 0.1mm. Draw this configuration properly and discuss briefly what will happen when the block is released. Show the forces acting on the sliding block when the velocity of the block is constant (dlosk = 0) and write down the force equation for the axis parallel to inclined surface (ignore the resistance due to air). Draw the linear velocity distribution across the thin layer of oil between the block and the inclined surface. Perform an internet search for the specific weight of steel (7steel) and the dynamic viscosity

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The distance between the centers of the two arms of a U-tube open to the atmosphere is 30 cm, and the U-tube contains 20 cm high alcohol in both arms. Now the U-tube is rotated about the left arm at 4.2 rad/s. Determine the elevation difference between the fluid surfaces in the tow arms. Include the free body diagram in your solution. a.0.96 m b.0.67 m c.0.33 m d.0.81 m
Flat plate, moves at speed u0 over a fixed plate, with the intermediate layer consisting of oil. a) If the velocity profile isparabolic (u2 = a ∙ y) find the stress on the moving plate. b) What is its value if the velocity profile is linear.Result: α) τ=-μu0/2d, β) τ=-μu0/d
The clutch system shown in the figure is used to transmit torque through a 2 mm thick oil film with μ = 0.38 N.s/m2 between two identical 30 cm diameter disks. When the driving shaft rotates at a speed of 1450 rpm, the driven shaft is observed to rotate at 1398 rpm. Determine the transmitted torque.
The clutch system shown in the figure is used to transmit torque through a 2-mm-thick oil film with ? = 0.38 N⋅s/m2 between two identical 30-cm-diameter disks. When the driving shaft rotates at a speed of 1200 rpm, the driven shaft is observed to rotate at 1125 rpm. Assuming a linear velocity profile for the oil film, determine the transmitted torque.
Determine the total force required to drag a thin plate which is placed in between two parallel plates 2.6 cm apart with the space filled with a fluid of viscosity of 0.55 Ns/m2.The area of the plate is 0.475 m2 and the speed at which it is dragged is 0.4 m/s. The position of thin plate from the top plate is 0.2 cm?
A thin plate travels between two plane, parallel, horizontal and stationary surfaces at a constant speed of 7 m/s. The two stationary surfaces are spaced 6 cm apart, and the middle is filled with oil of viscosity of 0.9 Ns/m2.The moving plate submerged in oil has a length of 2 m and a width of 0.5 m. (i) If the plate moves through the mid-plane between the surfaces, determine the force required to maintain this motion. (ii) Determine the force if the plate was 1 cm from the bottom surface and 2 cm from the top surface?
The surface tension of fluid in contact with air at 25oC is 0.51 n/m. The pressure inside a droplet is to be 0.05 N/cm2 greater than outside pressure. Determine the diameter of the droplet
Crude oil having a viscosity of 9.52 x 10(-4) lb-s/ft2 is contained between parallel plates. The bottom plate is fixed and upper plate moves when a forced P (lb) is applied. If the distance between the two plates is 0.1 in., what value of P is required to translate the plate with a velocity of 3 ft/s? The effective area of the upper plate is 200 in2.
pllllzzzz help me right nowww plzzz The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
The space between two parallel plates 0.001 ft apart is filled with oil viscosity 0.7cp. The top plate is stationary while the lower plate is moving in the x-direction with a velocity 1ft/sec. A. Determine shear rate B. What should be the shear stress in lbf/ft^2? Answer asap pls
A rectangular gate 1.8 m high by 1.20 m wide is mounted on the vertical wall of an open rectangular tank filled with oil. The top of the gate is 1.2 m below the surface of oil. What is the minimum force F applied at the top edge of the gate required to keep it close assuming the gate is hinged at the bottom edge. (S=0.8)
Q. 6 A 4.5-cm wide space between two plates is filled with SAE 30W lubricating oil at 26.7°C (Hoil = 0.301645 N.S/m2 ). What is the area of a very thin plate which is dragged by a force of 18 N through the oil at velocity of 16 m/min if the plate is 1.5 cm away from one of the fixed surfaces?