A cylinder with a 150 mm diameter and 300 mm length is put under a com-pressive load of 665 kN. The modulus of elasticity for this specimen is 55 GPa and Poisson’s ratio is 0.35. Calculate the final length and the final diameter ofthis specimen under this load assuming that the material remains within thelinear elastic region.

A cylinder with a 150 mm diameter and 300 mm length is put under a com-pressive load of 665 kN. The modulus of elasticity for this specimen is 55 GPa and Poisson’s ratio is 0.35. Calculate the final length and the final diameter ofthis specimen under this load assuming that the material remains within thelinear elastic region.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A cylinder with a 6.0 in. diameter and 12.0 in. long is put under a compressive load of 150,000 lbs. The modulus of elasticity for this specimen is 8,000,000 psi. and Poisson’s ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region.
A cylinder with a 6.0 in. diameter and 12.0 in. length is put under a compressive load of 150 kips. The modulus of elasticity for this specimen is 8,000 ksi and Poisson’s ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region.
A cylinder with a 150 mm diameter and 300mm length is put under a compressive load of 665 kips. The modulus of elasticity for this specimen is 55 GPa and Poisson’s ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region.
A metal rod with 0.5 in. diameter and 12.0 in. length is put under a compressive load of 150 kips. The modulus of elasticity for this specimen is 8,000 ksi and Poisson’s ratio is 0.35. Calculate the final length and the final diameter of this specimen under this load assuming that the material remains within the linear elastic region
A stainless-steel rod 16mm in diameter and 300mm long is put under a tensile load of 250 kN. Assuming that the modulus of elasticity for this specimen is 250,000 MPa and the final diameter is 15.96 mm. Calculate the final length, in mm, and the Poisson’s ratio of this specimen under this load assuming that the material remains within the linear elastic region.
a liquid compressed in a cylinder has a volume of 1500cm³ at 1 mn/m² and a volume of 1495 cm³ at 2mn/m² . determine the bulk modulus of elasticity. answer must be correct.
A cylindrical metal bar with a diameter of 12.83 mm is applied to a load of 17.8 kN. This loadproduces a reduction in diameter of 7.62 μm. The deformation is purely elastic. Determine thePoisson’s ratio of this material if the elastic modulus is 103.4 GPa?