A cylindrical tank contains three liquids of specific gravities: 0.80, 1.00, and 1.50. Each liquid has a thickness of 0.60m and the tank is 1.20m in diameter. If a circular orifice 100mm in diameter is placed at the bottom of the tank to drain the fluid contents with the coefficient of discharge C = 0.650, then: Determine the time to drain all the fluids completely. Group of answer choices 78 seconds 60 seconds 134 seconds 148 seconds

Q: A 150 mm diameter pipe carries 81.3 L/s of water. The pipe branches in to two pipes one is 50 mm in…

A:

Q: 1. At time t = 0 a tank contains Q, Ib of salt dissolved in 100 gal of water. Assume that water…

A: We have given the problem

Q: A sharp-edged orifice of 12.5 mm in diameter has a coefficient of discharge of 0.6 and is situated…

A: Diameter = 12.5 mm = 0.0125 m Coefficient of discharge = 0.6 Head = 1.8 m Density = 998 kg/m3…

Q: 1. Water flows through a pipe at a velocity of 3.25 m/s. What is the velocity head?  A. 0.632 m B.…

A:

Q: A cylindrical tank of diameter 0.8 meter is completely filled with water and its top surface is open…

A: Given data as per question Cylindrical tank of diameter = 0.8 meter  circular hole of diameter = 15…

Q: A prismatic vessel has two compartments A and B communicating by an orifice 0.3m square with C =…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: 21-50. A pump supplies water through a branching pipeline to two tanks A and B. The water surface…

A:

Q: Question 23 Glycerine at 30 °C is flowing between two large reservoirs. These reservoirs have…

A:

Q: The head in a vessel with vertical sides and a height of 4m at the instant of opening an orifice was…

A: When a tank with an orifice at the bottom is filled with water and the orifice is opened water is…

Q: In the system shown, the water discharge flow rate of 0.0025 m³/s is delivered through the 8 cm…

A: Given data: ◆ The diameter and length of the cast iron pipe: D = 8 cm = 0.08 m , L = 388 m ◆ The…

Q: A liquid of specific gravity 1.75 flows in 6 cm horizontal pipe. The total energy at a certain point…

A: Given:Specific gravity of liquid,s=1.75So,density of liquid=(1000×1.75)Kgm3=1750Kgm3Total…

Q: OIL FLOWS fRom PRESSURIZEFO TANK THE AIR AT A TO 8, DETERMノん法 THE PRESSURE AT A TO CAUSE A FLOW OF…

A:

Q: 7. For the flow of a thin layer of liquid down an inclined plane shown: a. Using the cross-hatched…

A: As per company policy, we are restricted to solve three sub-part of one question at a time. Please…

Q: A circular orifice 15-mm-diameter is located at the bottom of a tank 0.5 m2 in plan area.  At a…

A:

Q: 2.attention to the piping system shown in the figure below. Pipes 1, 2, and 3 are installed in…

A:

Q: For the system shown, the pipe is steel with an internal diameter of 100 mm. Water is pumped through…

A: We have to determine The discharge at Point D is to the atmosphere. The pumping rate (m/min) is most…

Q: A sharp-edged orifice of 12.5 mm in diameter has a coefficient of discharge of 0.6 and is situated…

A: Given:Diameter of orificed=12.5mm=0.0125mcoefficient of dischargecd=0.6head of water above…

Q: Oil flows thru a 50 mm diameter pipe having a head loss of 12 m. The length of the pipe is 120 m.…

A:

Q: A 28-in pump is used to deliver water from a lower reservoir to a higher reservoir . The total…

A: Given:d=10 inL=62 ftf=0.022H=365-0.04718Q2

Q: Following the pump, the pressure in a 6-inch inner smooth pipe conveying water is 20 pounds per…

A:

Q: You are working as a trainee engineering in a company ABC, is the leading manufacturing company for…

A:

Q: 60 kg Q.2. Oil flows steadily through the pipe shown in Figure. If the flux through the pipe is 350…

A: The total pressure energy is conserved, if the losses due to friction and bending of the pipe are…

Q: A horizontal pipe of diameter 550 mm is suddenly contracted to a diameter of 300 mm. The pressure…

A:

Q: Water flowing through a pipe of constant cross section, 11 cm in diameter, as shown in Fig. shown in…

A:

Q: 6. Water flowing through a pipe with a flow rate of 2.2 m3/s and a pressure of 85 kPa. Determine the…

A: Given data: The initial diameter of the pipe is d1 = 1 mThe initial area of the pipe is A1 = (π/4) x…

Q: An orifice has a coefficient of discharge of 0.62 and a coefficient of contraction of 0.64.…

A: Finding Cv

Q: A hole of are 2 mm^2 opens in the pipe near the lower end of a large water-storage tank, and stream…

A:

Q: Freshwater at a temperature of 10°C flows at a rate of 0.10 m3/sec through the piping system…

A: Determine the value of the absolute roughness of the galvanized iron pipe.

Q: The air is measured at 48 deg. C and 511mm Hg. The duct diameter is 553 mm while the discharge…

A:

Q: The discharge of water in the given pump is given as 0.030 cubic meters per seconds. Use Ywater 9.79…

A:

Q: A sludge mixture having a specific gravity of 2.93 and a viscosity of 0.09 grams per centimeter…

A: Given data Specific gravity = 2.93 Viscosity = 0.09  g/(cm•s) = 0.009 N-s/m^2 Pipe diameter = 2.5…

Q: Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow rate in…

A:

Q: The two pumps are arranged in parallel to supply water for a total static head of 40 ft. The…

A: Given: Total static head→H=40 ft Diameter of the pipe→D=10 in=0.83 ft Length of the pipe→L=1200 ft…

Q: Water is pumped at a rate of 21.4 m/s from tank (A) and out through a 300.5 m pipe to tank (B). The…

A: Given details: Q= 21.4 m3 L= 300.5 m H= 70 m f= 0.02 Note: Inbuilt math type is not proper work so…

Q: A 300mm x 300mm pipe discharges 600 L/s of water where the length is 300m. Determine the head loss…

A:

Q: A piezometer and a Pitot tube are tapped into a 3-cmdiameter horizontal water pipe, and the height…

A:

Q: A sharp - edged orifice of 12,5mm in diameter has a coefficient of discharge of 0.6 and is situated…

A:

Q: A sharp-edged orifice of 12.5 mm in diameter has a coefficient of discharge of 0.6 and is situated…

A: Given, Mass flow rate, m˙ =90kg/minDensity of water, ρw=998kg/m3Diameter of orifice,…

Q: D. The water is flowing through a tapering pipe having cross section areas 0.2 m2 and 0.1 m2 at…

A:

Q: Calculate the liquid rates of flow in both sections. Calculate the ratio of the rates of flow.…

A: Flow = Q = A v A = area of cross section V = velocity

Q: Water is discharged into the atmosphere from the pipe at 14 m/s (Figure 1). Neglect the resistance…

A: Given: V=14 m/s

Q: Air flows through a Venturi channel of rectangular cross-section as shown in Figure 1. The constant…

A: Given data: - The constant width of the channel is b = 0.08 m. The height at the exit is h4 = 0.04…

Q: Water at 10°C flows through the system shown in the figure below at 0.34 m/s. Energy loss in the…

A:

Q: B4. An orifice meter with orifice area 931 mm² is inserted in a pipe of area 1862 mm2 .The pressure…

A: According to the given information, we have an area of orifice meter  931 mm2, area of pip is…

Q: Water (ν = 0.86x10-6m2/s) flows through a tube with the diameter 12 mm at a velocity of 2 m/s.…

A:

Q: Water flowing through a pipe of constant cross section, 11 cm in diameter, as shown in Fig. shown in…

A:

Q: A venturi meter with diameter at inlet D1, and throat diameter D2, is used for measuring the flow of…

A:

Q: Q/ A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length…

A:

Q: The discharge of water in the given pump is given as 0.030 cubic meters per seconds. Use ywater =…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.