- A multiple disc clutch has three discs on the driving shaft and two on the providing four pairs of contact surface. The outer diameter of the contact surface is 25 cm and the inner diameter is 15 cm. Determine the Max. axial intensity of pressure between the discs for transmitting 25 h.p power at 500 r.p.m. Assuming uniform wear and coefficient of friction as 0.3

- A multiple disc clutch has three discs on the driving shaft and two on the providing four pairs of contact surface. The outer diameter of the contact surface is 25 cm and the inner diameter is 15 cm. Determine the Max. axial intensity of pressure between the discs for transmitting 25 h.p power at 500 r.p.m. Assuming uniform wear and coefficient of friction as 0.3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An open belt running over two pulleys 24 em and 60 cm diameters connects two parallel shafts 3 m apart and transmits 3.75 KW from the smaller pulley that rotates at 300 r.p.m. coefficient of friction between the belt and the pulleys is 0.3 and the safe working tension is 100 N/em width. Determine: i) minimum width of the belt, ii) initial belt tension, and i) length of the belt required.
Determine the size of the clutch plate suitable for an Ambassador car employing a single plate type friction clutch and developing 37.5 kW at 4282rpm. The inside diameter of the clutch plate is 0.6 times its outside diameter and it is to be ensured that even after a loss of 30% of the engine torque due to wear of the clutch facing, the clutchdoesn’t slip. The intensity of the pressure on the facing is not to exceed 70 kPa. Assume µ = 0.3.
A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch. Subject: Theory of Machines
A flat belt, of density 1000 kg/m3 has a maximum permissible stress of 2·5 MN/m². Thebelt is 200 mm wide and 12 mm thick.(a) Determine the maximum power that can be transmitted if the ratio of tight-side toslack-side tension is 2. The diameter of the driving pulley is 900 mm and the required speed of the output shaft is955 rev/min(b) Taking the belt thickness into account, determine the required diameter of theoutput pulley. (c) What would the required diameter be, assuming a total slip of 4%? (d) If the mass of the belt was neglected, explain the effect (with reasons) this wouldhave on the maximum power calculated in (a)
An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 m apart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted. [Ans. 2.39 kW]
The diameter of the pulley on the compressor shaft must not be greater than 1.2 metre while the centre distance between the pulleys is limited to 1.85 metre. A compressor, requiring 95000W is to run at about 500 r.p.m. The drive is by V- belts from an electric motor running at 1500 r.p.m. The belt speed should not exceed 1500 m/min. The coefficient of friction between the belt and the pulley is 0.3. Determine the number of V-belts required to transmit the power if each belt has a crosssectional area of 3 cm2, density 1100 kg/m3 and an allowable tensile stress of 3 MPa. The groove angle of the pulley is 50°. Calculate also the length required of each belt.
Initial condition: P = 8 MPax = 100%m = 5 kgProcess: IsothermalFinal condition: Q in KJ = 75% of h1Required: Work
A leather belt is required to transmit 7.5 Kw of power from a pulley 1.2m in diameter at 250 rpm. The lap angle (contact angle between small pulley and belt) is 165o and the coefficient of friction of friction between the belt and the pulley is 0.3. If the safe working stress for the leather belt is 1.5 MPa, density of leather 1 Mg/m3 and thickness of belt 10 mm, determine the tension in the both (tight and slack) side and width of the belt taking centrifugal tension into account.
3.4 A storage tank is 5 m in diameter, 4 m high and the density of the fluid itcontains is 795 kg/m3. Determine the required wall thickness if the yieldstress of the material is 325 MPa, the factor of safety is 10 and the efficiency ofthe longitudinal joint is 80 %.
7.An exhaust fan fitted with 900 mm diameter pulley is driven by a flat belt from a 30 kW, 950 r.p.m. squirrel cage motor. The pulley on the motor shaft is 250 mm in diameter and the centre distance between the fan and motor is 2.25 m. The belt is 100 mm wide with a coefficient of friction of 0.25. If the allowable stress in the belt material is not to exceed 2 MPa, determine the necessary thickness of the belt and its total length. Take centrifugal force effect into consideration for density of belt being 950 kg/m3. [
....An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley is 2.89 rad and the belt speed runs at 29.36 m/s. The groove angle of the pulleys is 35°. Determine the tension in the slack side of the belt in N if the belt has a cross-sectional area of 366 mm2, density 1000 kg/m3, and an allowable tensile stress of 2.3 MPa. The coefficient of friction between the belt and the pulley is 0.3
A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with a yield value of 64ksi holding the cylinder head to the compressor. Determine the tensile stress of the bolt.