A THREE-PHASE CIRCUIT WHERE THE BALANCED DELTA LOAD OF 36 + J54 OHMS IS SUPPLIED BY 8,602 OHMS IMPEDANCE CONDUCTORS WITH A PHASE ANGLE OF 54,462 DEGREES. IF THE GENERATOR VOLTAGE IN PHASE B IS 100 VOLTS ANGLE - 120 DEGREES. CALCULATE: A) THE VOLTAGE BC IN LOAD. B) THE POWERS IN THE CONDUCTORS. C) THE POWER TRIANGLE IN THE LOAD.

A THREE-PHASE CIRCUIT WHERE THE BALANCED DELTA LOAD OF 36 + J54 OHMS IS SUPPLIED BY 8,602 OHMS IMPEDANCE CONDUCTORS WITH A PHASE ANGLE OF 54,462 DEGREES. IF THE GENERATOR VOLTAGE IN PHASE B IS 100 VOLTS ANGLE - 120 DEGREES. CALCULATE: A) THE VOLTAGE BC IN LOAD. B) THE POWERS IN THE CONDUCTORS. C) THE POWER TRIANGLE IN THE LOAD.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.47P: Two three-phase generators supply a three-phase load through separate three-phase lines. The load...

See similar textbooks

Similar questions

Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances including the load impedance in per-unit. The data are given a follows: G:90MVA22kVx=0.18perunitT1:50MVA22/220kVx=0.10perunitT2:40MVA220/11kVx=0.06perunitT3:40MVA22/110kVx=0.064perunitT4:40MVA110/11kVx=0.08perunitM:66.5MVA10.45kVx=0.185perunit Lines I and 2 have series reactances of 48.4 and 65.43, respectively. At bus 4, the three-phase load absorbs 57 MVA at 10.45 kV and 0.6 power factor lagging.
With generator conyention, where the current leaves the positive terminal of the circuit element, if P is positive then positive real power is delivered. (a) False (b) True
Does an open connection permit balanced three-phase operation? - (a) Yes (b) No
Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line currents as well as the neutral current are always zero. (a) True (b) False
A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated distribution feeder. The load can be mode led by an impedance of ZL=(4.7+j9)/phase, wye-connected. The impedance of the phase conductors is (0.3+j1). Determine the following by using the phase A to neutral voltage as a reference and assume positive phase sequence: (a) Line currents for phases A, B, and C. (b) Line-to-neutral voltages for all three phases at the load. (c) Apparent. active, and reactive power dissipated per phase, and for all three phases in the load. (d) Active power losses per phase and for all three phases in the phase conductors.
One advantage of balanced three-phase systems over separate singlephase systems is reduced capital and operating costs of transmission and distribution. (a) True (b) False
In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the line-to-neutral voltages are always equal to zero. (a) False (b) True
An Alternator having three-phase, 3-wire ABC system supplying an effective line voltage of 120 V, has an athree-impedances of 50 / 45 ohms in Delta connection. Assume that Vbc is the reference vector. Determine a) linecurrent and line voltages with its degrees, b)Draw the current –voltage phasor diagram c) and the power generated inthe line quantities of the alternator.
Non-Reactive Loads of 10kW, 20kW and 12kW are connected between the neutral and the red, yellow and blue phases respectively of 3-phase, 4 wire . The line voltage is 400. If a three phase motor is now started ,taking 150 A from the lines at a power factor of 0.3 lagging What should be the total current in each line and the neutral wire? Find the total real and reactive power supplied to the loads
The terminal voltage of a 3-φ generator is 19053 V, line-to-line. The load draws a current of 1515 A, leading, with a phase angle of 30o. The total real power, drawn by the load would be:
The IAC current of a balanced three-phase delta connected load is known as 10 Amps (-10 degrees) and the VAB voltage as 20 Volts (10 degrees). Accordingly, calculate the following expressions by considering the positive phase sequence. A) IAB=? B)load impedance=? C)IBC=?
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer