A uniform bar whose mass and length are 55.0 kg and 8.00 m, respectively is supported by two light cables as shown. An 87.0 kg painter stands 1.25 m from the left end of the bar, and his equipment is 2.25 m from the right end. If the tension in the left cable is twice as the right cable, what are the tensions in the cable and the mass of the equipment? L=8.00 m

A uniform bar whose mass and length are 55.0 kg and 8.00 m, respectively is supported by two light cables as shown. An 87.0 kg painter stands 1.25 m from the left end of the bar, and his equipment is 2.25 m from the right end. If the tension in the left cable is twice as the right cable, what are the tensions in the cable and the mass of the equipment? L=8.00 m

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 30PQ: A 5.45-N beam of uniform density is 1.60 m long. The beam is supported at an angle of 35.0 by a...

See similar textbooks

Similar questions

A 5.45-N beam of uniform density is 1.60 m long. The beam is supported at an angle of 35.0 by a cable attached to one end. There is a pin through the other end of the beam (Fig. P14.30). Use the values given in the figure to find the tension in the cable. FIGURE P14.30
A person carries a plank of wood 2.00 m long with one hand pushing down on it at one end with a force F1 and the other hand holding it up at .500 m from the end of the plank with force F2. If the plank has a mass of 20.0 kg and its center of gravity is at the middle of the plank, what are the magnitudes of the forces F1 and F2?
A brass wire and a steel wire, both of the same length, are extended by 1.0 mm under the same force. Is the cross-sectional radius of the brass wire more, less, or equal to the cross-sectional radius of the steel wire? Explain. Youngs moduli for brass and steel are 1.0 1010 N/m2 and 2.0 1011 N/m2, respectively.
At a museum, a 1300-kg model aircraft is hung from a lightweight beam of length 12.0 m that is free to pivot about its base and is supported by a massless cable (Fig. P14.38). Ignore the mass of the beam. a. What is the tension in the section of the cable between the beam and the wall? b. What are the horizontal and vertical forces that the pivot exerts on the beam? FIGURE P14.38 (a) From the free-body diagram, the angle that the string tension makes with the beam is = 55.0 + 18.0 = 73.0, and the perpendicular component of the string tension is FT sin73.0. Summing torques around the base of the rod gives (Eq. 14.2): =0:(12.0m)(1300kg)(9.81m/s2)cos55.0+FT(12.0m)sin73.0=0FT=(12.0m)(1300kg)(9.81m/s2)cos55.0(12.0m)sin73.0FT=7.65103N Figure P14.38ANS (b) Using force balance (Eq. 14.1): Fx=0:FHFTcos18.0=0FH=FTcos18.0=[(12.0m)(1300kg)(9.81m/s2)cos55.0(12.0m)sin73.0]cos18.0=7.27103NFy=0:FVFTsin18.0(1300kg)(9.81m/s2)=0 FV=FTsin18.0+(1300kg)gFV=[(12.0m)(1300kg)(9.81m/s2)cos55.0(12.0m)sin73.0]sin18.0+(1300kg)(9.81m/s2)FV=1.51104N
One end of a uniform 4.00-m-long rod of weight Fg is supported by a cable at an angle of = 37 with the rod. The other end rests against the wall, where it is held by friction as shown in Figure P12.23. The coefficient of static friction between the wall and the rod is s= 0.500. Determine tile minimum distance x from point A at which an additional object, also with the same weight Fg can be hung without causing the rod to slip at point A.
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.
Suppose the weight of the drawbridge in Figure 9.34 is supported entirely by its hinges and the opposite shore, so that its cables are slack. (a) What fraction of the weight is supported by the opposite shore if the point of support is directly beneath the cable attachments? (b) What is the direction and magnitude of the force the hinges exert on the bridge under these circumstances? The mass of the bridge is 2500 kg.
A uniform drawbridge must be held at a 37.5 ∘∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 NN, is 16.5 mm long, and pivots about a hinge at its lower end. A cable is connected 3.00 mm from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. 1)What is the tension in the cable? 2)Find the magnitude of the force the hinge exerts on the bridge. 3)Find the direction of the force the hinge exerts on the bridge. 4)If the cable suddenly breaks, what is the initial angular acceleration of the bridge?
A uniform beam 4.2 m long and weighing 2200 N carries a 3700 N weight 1.50 m from the far end, as shown in the figure below. It is supported horizontally by a hinge at the wall and a metal wire at the far end. 1) How strong does the wire have to be? That is, what is the minimum tension it must be able to support without breaking? Express your answer in newtons. 2) What are the horizontal component of the force that the hinge exerts on the beam? Express your answer in newtons. 3) What are the vertical component of the force that the hinge exerts on the beam? Express your answer in newtons.
A uniform 37.0 kg scaffold of length 6.2 m is supported by two light cables, as shown below. An 82.0 kg painter stands 1.0 m from the left end of the scaffold, and his painting equipment is 1.6 mfrom the right end. If the tension in the left cable is twice that in the right cable, find the tensions in the cables (in N) and the mass of the equipment (in kg). (Due to the nature of this problem, do not use rounded intermediate values in your calculations).
A uniform 37.0 kg scaffold of length 5.8 m is supported by two light cables, as shown below. A 78.0 kg painter stands 1.0 m from the left end of the scaffold, and his painting equipment is 1.3 m from the right end. If the tension in the left cable is twice that in the right cable, find the tensions in the cables (in N) and the mass of the equipment (in kg). (Due to the nature of this problem, do not use rounded intermediate values in your calculations—including answers submitted in WebAssign.) Tension in the left cable